Leviton QuickPort RCA 110 Directives D'utilisation

RCA 110-Type
QuickPort ® Connectors
Conector RCA Tipo 110
Quickport MR
Connecteur RCA
QuickPort MD de type
110
1
2
3
A Division of Leviton Manufacturing Co.,Inc.
Phone: (425) 485-4288
Fax: (425) 483-5270
www.levitonvoicedata.com
40735-R**
Instructions for Use
RCA 110-Type QuickPort ® Connectors
DESCRIPTION
Leviton's RCA 110-Type QuickPort Connector is designed to
locally distribute baseband audio/video signals over unshielded
twisted pair cabling. Featuring standard IDC slots for quick and
easy terminations, these connectors are compatible with a
variety of QuickPort wallplates and panels.
INSTALLATION
1. Remove approximately 2˝ of cable jacket from cable.
2. Note the color coded label located between the IDC
connector slots, including pin numbers. (Figure 1)
3. Route the wires for termination. Terminate one pair at a
time, placing cable so that the jacket touches the
connector's edge. Start from the side of cable entry.
NOTE: Terminating each pair after placement will prevent
crushing the inside pairs with the punch down tool.
4. Using a 110-style impact tool (set to low), seat the wires
into the IDC slots. Maintain wire pair twisting as close as
possible to the IDC contact. Must be 1/2˝ or less. (Figure 2)
5. Place the cap over the terminated wires for secure
connection and added strain relief. (Figure 3)
6. Insert connector assembly into platform or wallplate. Note
the "UP" position of the connector.
NOTE: In some QuickPort applications, RCA 110-Type
Connectors may be too wide for adjacent installations.
IMPORTANT INSTRUCTIONS
1.
Read and understand all instructions. Follow all warnings
and instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub, wash
basin, kitchen sink or laundry tub, in a wet basement, or
near a swimming pool.
3.
Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION
1.
Never install communications wiring or components during a
lightning storm.
2.
Never install communications components in wet locations
unless the components are designed specifically for use in
wet locations.
3.
Never touch uninsulated wires or terminals unless the wiring
has been disconnected at the network interface.
4.
Use caution when installing or modifying communications
wiring or components.
5.
To prevent electrical shock, each opening must be filled with
a module.
RCA 110-Type
QuickPort ® Connectors
Conector RCA Tipo 110
Quickport MR
Connecteur RCA
QuickPort MD de type
110
1
2
3
A Division of Leviton Manufacturing Co.,Inc.
Phone: (425) 485-4288
Fax: (425) 483-5270
www.levitonvoicedata.com
40735-R**
Instructions for Use
RCA 110-Type QuickPort ® Connectors
DESCRIPTION
Leviton's RCA 110-Type QuickPort Connector is designed to
locally distribute baseband audio/video signals over unshielded
twisted pair cabling. Featuring standard IDC slots for quick and
easy terminations, these connectors are compatible with a
variety of QuickPort wallplates and panels.
INSTALLATION
1. Remove approximately 2˝ of cable jacket from cable.
2. Note the color coded label located between the IDC
connector slots, including pin numbers. (Figure 1)
3. Route the wires for termination. Terminate one pair at a
time, placing cable so that the jacket touches the
connector's edge. Start from the side of cable entry.
NOTE: Terminating each pair after placement will prevent
crushing the inside pairs with the punch down tool.
4. Using a 110-style impact tool (set to low), seat the wires
into the IDC slots. Maintain wire pair twisting as close as
possible to the IDC contact. Must be 1/2˝ or less. (Figure 2)
5. Place the cap over the terminated wires for secure
connection and added strain relief. (Figure 3)
6. Insert connector assembly into platform or wallplate. Note
the "UP" position of the connector.
NOTE: In some QuickPort applications, RCA 110-Type
Connectors may be too wide for adjacent installations.
IMPORTANT INSTRUCTIONS
1.
Read and understand all instructions. Follow all warnings
and instructions marked on the product.
2.
Do not use this product near water—e.g., near a tub, wash
basin, kitchen sink or laundry tub, in a wet basement, or
near a swimming pool.
3.
Never push objects of any kind into this product through
openings, as they may touch dangerous voltages.
4.
SAVE THESE INSTRUCTIONS.
SAFETY INFORMATION
1.
Never install communications wiring or components during a
lightning storm.
2.
Never install communications components in wet locations
unless the components are designed specifically for use in
wet locations.
3.
Never touch uninsulated wires or terminals unless the wiring
has been disconnected at the network interface.
4.
Use caution when installing or modifying communications
wiring or components.
5.
To prevent electrical shock, each opening must be filled with
a module.