Télécharger Imprimer la page

Wood's Powr-Grip 914791320 Instructions

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

CO., INC.
VACUUM CUP
INSTRUCTIONS
- for all cup sizes listed hereafter -
Rev. 1.2 / 02-09 Instruction Sheet 32630
SPECIFICATIONS
Product Description
Vacuum cups use vacuum to mount loads temporarily or to lift and carry loads,
as follows: A manual pump removes air from between the rubber pad and the
contact surface; a red line on the pump's plunger serves as a vacuum indicator; a
check valve allows the user to repump the cup without removing it from the contact
surface; and a release mechanism allows the cup to disengage completely
Nominal Size
Maximum Load Capacity*
3" [77 mm] diameter
15 lbs [7 kg]
3" x 6" [77 mm x 153 mm]
40 lbs [18 kg]
4½" [115 mm] diameter
40 lbs [18 kg]
6" [153 mm] diameter
70 lbs [32 kg]
*Maximum Load Capacity includes a 3:1 safety factor and requires the following:
attachment on clean, smooth, nonporous flat surfaces; a minimum vacuum level
of 17½" Hg [-59 kPa]; and a friction coefficient of 1. This rating is based on tests
of new vacuum cups attached to the upper, horizontal surface of static objects in
ideal conditions. Many factors can reduce the capacity, including: attaching cups on
vertical or inclined surfaces to lift a load or to mount a load; dynamic loading (eg,
mounting loads on moving vehicles); or attaching loads that apply leverage to the
cup. See www.powrgrip.com for more information.
Contact Surface and Environmental Conditions
Use the cup on clean, relatively smooth, nonporous surfaces, at temperatures from
0° to 120° Fahrenheit [-18° to 49° Celsius]. Moisture or contaminants can reduce
the slip resistance of the cup. The red-line indicator may not perform reliably at
elevations above 5000 feet [1524 meters]; see Service.
OPERATION
To Attach
1) Clean the contact surface and, if needed, the face of the vacuum cup (see
Cleaning). CAUTION: Test the cup for staining or deformation of surfaces with
light colors or soft coatings.
2) Position the cup so the red line will be visible if it should appear while the cup is
attached.
3) Pump the plunger until the cup attaches completely. When the red line is hidden,
the cup is ready for use.
4) Check the plunger frequently to make sure the cup remains securely attached.
If the red line appears, pump the plunger until the red line is hidden again (see
WARNINGS).
To Release
1) Secure the load.
2) Pull a release tab until the cup disengages completely. CAUTION: Remove the
cup when not in use. If the cup remains attached to a hot surface (eg, in direct
sunlight) for an extended time, the rubber pad could bond with the surface,
resulting in damage to the surface or to the pad when it is removed.
MAINTENANCE
Service
Regularly make sure the vacuum cup's air filter is in place. If not, discontinue use
until the filter is replaced.
CO., INC.
®
1.
60024
Air Filter
2.
Release Tab
3.
Plunger
4.
Red Line
5.
90111
Pump
6.
49345T
Vacuum Pad, 4 1/2" Dia. (LJ45)
49386T
Vacuum Pad, 6" Dia. (TL6)
49396T
Vacuum Pad, 6" Dia. (TL6T / for Rigid Handle)
49426T
Vacuum Pad, 6" Dia. (LP6)
7.
10014
Screw, 10-32 x 7/16"
10024
Screw, 10-32 x 5/8" (for 4 1/2" pad only)
8.
50220
Accessory Mount, Aluminum (for Tie-Down or Flip Handle)
50210
Accessory Mount, Aluminum, 1/4-20 Stud
60181
Accessory Mount, Polycarbonate, 1/4-20 Insert
60180
Accessory Mount, Polycarbonate, 1/4-20 Stud
9.
50230
Rigid Handle
10. 15790
T-Handle (fits on 1/4-20 stud)
11. 50100
Tie-Down
12. 50102
Flip Handle
SC
13. 10156
Screw, 10-32 x 1/4"
14. 60118
Accessory Mount, 1/4-20 Stud
.
P.O. Box 368 / 908 West Main 1-800-548-7341
Laurel, MT 59044
®
U.S.A.
15. 60116
16. 49365T
17. 49326T
18. 10008
Since aging and wear reduce the capacity of the rubber pad, it should be replaced
at least once every 2 years or whenever damage is discovered.
If the cup does not function normally, the cup face may be dirty or damaged, or the
pump may require service. First clean the cup face according to the directions to
follow. If the problem persists, contact an authorized dealer or visit www.powrgrip.
com for assistance.
Cleaning
1) Remove the air filter from the cup face.
2) Use a clean sponge or lint-free cloth to apply Wood's Powr-Grip
Cleaner to the cup face. Soapy water or other mild cleansers may also be used;
see WARNINGS and www.powrgrip.com for more information. CAUTION: To
prevent liquid from contaminating the pump, hold the cup face-down or cover the
suction hole in the filter recess.
3) Wipe all residue from the cup face.
4) Allow the cup to dry and reinstall the air filter.
Storage
Store in a clean, dry location out of direct sunlight. Protect the cup face from
damage using the pad cover (when supplied) or another appropriate means.
WARNINGS
Failure to observe WARNINGS could damage the vacuum cup or the load, or cause
injury to the user.
• Do not use the cup to support loads that exceed the Maximum Load Capacity or
the effective capacity (see SPECIFICATIONS).
• Do not use the cup to support a person.
• Do not use the cup to support loads which could injure people if the cup
disengages unexpectedly.
• Do not place the cup face against surfaces which could damage the sealing edge
of the rubber pad.
• Avoid conditions that could cause the cup to slip or to disengage prematurely,
such as: contaminants, cuts or scratches in the cup face or contact surface;
applying the cup to porous materials; or applying pressure against the cup edge.
• Do not use the cup when the red line is visible. If the red line reappears
frequently, discontinue use and see Service.
• Do not allow anything to interfere with free movement of the plunger while the cup
is attached.
• Do not touch any release tab while using the cup.
• Do not leave the cup in use and unattended.
• Do not use harsh chemicals (such as solvents or gasoline) or unauthorized
rubber cleaners and conditioners to clean the cup.
Fax: 1-406-628-8354
1-406-628-8231
www.powrgrip.com
Handi-Grip Handle (for 3" x 6" pad)
50205
Handi-Grip Handle (for 4 1/2" and 6" pads)
Vacuum Pad, 3" x 6" (RF36)
Vacuum Pad, 3" Dia. (TL3)
Screw, 10-32 x 3/8"
Not Shown
28675
Wood's Powr-Grip
Vacuum Cup Cleaner
®
29306MM Pad Cover, 3"
29308
Pad Cover, 4 1/2"
29312
Pad Cover, 6"
®
Vacuum Cup
Products are manufactured under an
ISO 9001 quality management system
R
S
S
0

Publicité

loading

Sommaire des Matières pour Wood's Powr-Grip 914791320

  • Page 1 1) Remove the air filter from the cup face. Nominal Size Maximum Load Capacity* 2) Use a clean sponge or lint-free cloth to apply Wood's Powr-Grip ® Vacuum Cup 3" [77 mm] diameter 15 lbs [7 kg] Cleaner to the cup face.
  • Page 2 60180 Montura de accesorios, policarbonato, 1/4-20 macho 50230 Mango fijo 28675 Limpiador de ventosas de Wood's Powr-Grip ® 10. 15790 Mango en T (para 1/4-20 macho) 29306MM Cubierta de ventosa, 77 mm 11. 50100 ‘Tie-Down’ (asa de amarre)
  • Page 3 15 livres [7 kg] 2) Utilisez une éponge nette ou un chiffon net et peluche-libre pour appliquer sur la face de la ventouse le produit de nettoyage pour ventouses de Wood's 3 x 6 po [77 mm x 153 mm]...
  • Page 4 60181 Halterung, Polykarbonat, 1/4-20 Innengewindebuchse 60180 Halterung, Polykarbonat, 1/4-20 Gewindebolzen ohne Abbildung 9. 50230 starrer Handgriff 28675 Reiniger des Vakuumsaugers von Wood's Powr-Grip ® 10. 15790 T-Handgriff (Passt auf 1/4-20 Gewindebolzen) 29306MM Saugerkappe, 77 mm 11. 50100 Bügel 29308 Saugerkappe, 115 mm 12.