Richelieu RC-LTPS-DIM-PS-100 Guide De Démarrage Rapide

QUICK START GUIDE
Before you begin
When using electrical products, basic precautions
should always be practiced including the following:
• Read and follow all instructions that are on the
product or provided with the product.
• Reference the National Electrical Code, ANSI/NF-
PA 70, specifically for the installation of wiring
and clearances from power and lighting conduc-
tors.
What's included
1× dimmable LED power supply with AC input cord +
switch + NEMA-1-15P plug, DC output wire + DC
quick-connect 2510HXH 6-port hub + quick-connect
10-port hub Micro24.
Installation steps
1. Install the enclosed LED power supply (driver) at
the desired location using appropriate Ф3-4mm
screws/bolts/anchors (not supplied).
2. Connect the green cable to the ground.
3. Plug the LED strip with leads equipped with
quick-connect DC plug into a socket (port) of the
corresponding DC quick-connect hub.
4. Plug the power supply into an AC socket.
5. Use the switch on the AC input cord to power the
LED strips.
DIMMING
Use with forward & reverse
phase, ELV, Triac dimmers
4
5
1
Note: your product may appear different
from this illustration.
Dimming/Hardwired Installation
Your power supply can be hardwired to a dimmer. The
following steps should only be performed by a
qualified electrician, in accordance with all applica-
ble national and local building, electrical and other
codes and standards.
1. Unscrew the junction box cover, remove
knockouts at needed input and output locations
and install knockout connectors into the produced
openings.
2. Electrical connection:
a. Refer to the dimmer documentation for
dimmer wiring instructions.
b. Pass AC input and DC output wires through
knockout connectors. Connect black (L - live)
and white (N - neutral) wires AC input to
corresponding LED Driver input, green or bare
copper wire (ground) to ground; output red
(DC+) and black (DC-) wires to LED lighting.
Use appropriate wire nuts (not supplied) to
connect wires.
3. Reinstall junction box cover, secure it with screws.
4. Power and test the circuit.
3
2
2510HXH
MODELS: RC-LTPS-DIM-PS-100|130VAC-CV-24V-25W-ELV-PG-DRBX (30142425)
RC-LTPS-DIM-PS-100|130VAC-CV-24V-50W-ELV-PG-DRBX (30142450)
Important safety notes
1. For indoor use only. The minimum conductor
temperature rating is 90°C.
2. Unplug/Disconnect the LED driver before making
or breaking connections to the equipment. A
disconnect device should be incorporated in the
field wiring.
3. The LED driver is not to be repaired and not to be
used any longer if it is damaged or defective.
4. The protective devices cannot be reset or replaced
after a short circuit or an overload.
5. The LED Driver does not rely upon the luminaire
enclosure for protection against accidental
contact with live parts.
6. All electrical connections must be in accordance
with local and national electrical codes. Refer to a
qualified electrician if you have any questions on
that matter. Installation work and electrical wiring
must be done by a qualified person in accordance
with all applicable codes and standards, including
fire-rated construction.
WARNINGS
1. Do not reverse polarity:
DC output: red="+", black ="-"
2. Risk of Electric Shock: When used in a
humid environment, install only on a circuit
protected by a Class A GFCI.
3. Risk of Fire: Installation involves special
wiring methods to run wiring through a
building structure. Consult a qualified
electrician.
4. Risk of Electric Shock: Mount the unit
higher that 1 foot from the ground level.
5. Risk of Fire: Do not connect LED strips with
a total rated power exceeding 80% of the
power supply.
6. Use Micro24 type connectors and connec-
1
tion hub only with 24VDC power supply.
Look for the blue "24VDC" sticker.
When performing wire connection, make sure
that the positive wire (writing) is aligned with
the positive pin of the LED strip and the negative
wire (lines) is aligned with the negative pin of
the LED strip.
Micro24
SAVE THESE INSTRUCTIONS
This guide contains important safety and
operating instructions for power units.
7900 Boul. Henri-Bourassa Ouest, St-Laurent, Québec, Canada, H4S 1V4
1 800 361-6000
www.richelieu.com