MyQ 041-0041 Mode D'emploi

Installation
Introduction
Your camera is accessible at the opener's bottom side. After installing
the new camera, use your myQ app to connect your new camera to
®
your myQ account.
®
To prevent possible
SERIOUS INJURY or DEATH:
• Disconnect ALL electric
and battery power BEFORE
performing ANY service or
maintenance.
To prevent damage to the camera,
push the camera lens closed when
replacing, and hold it in place as
you remove securing hardware.
DO NOT touch the camera logic
board during installation.
ALWAYS wear protective gloves
and eye protection when changing
the battery or working around the
battery compartment.
WARNING: This
product can
expose you to
chemicals including lead,
which are known to the
State of California to cause
cancer or birth defects or
other reproductive harm.
For more information go to
www.P65Warnings.ca.gov.
NOTICE: This device complies with part 15 of the FCC rules and
Innovation, Science and Economic Development Canada licence-exempt
RSSs. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation. Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
the equipment.
This device must be installed to ensure a minimum 20 cm (8 in.) distance
is maintained between users/bystanders and device.
This device has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules and Industry Canada
ICES standard. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The device for operation in the band 5150-5250 MHz is only for indoor
use to reduce the potential for harmful interference to co-channel mobile
satellite systems.
1.
Disconnect
power to the
garage door
opener,
and remove
the backup
battery, if
used.
4.
Lower the
camera
and unplug
the wire
harness.
7.
Attach
the new
decorative
ring.
Decorative
Ring
CAMERA SERVICE KIT REPLACEMENT
Hardware:
• Screw Qty. (3)
• Decorative Ring
• Camera
2.
Remove the
decorative
ring at the
opener's
bottom.
Decorative
Ring
5.
Plug in
the new
camera.
8.
Reconnect
power and
battery, if
used.
10.
Follow the myQ App instructions to add
®
the new camera to your myQ ® account.
NOTE: Only the replacement camera needs
to be provisioned (not the garage door
opener) using myQ app.
®
Camera LED Status Indicators
WHAT YOU SEE WHAT IT MEANS
Solid White Camera is powering up.
Flashing Blue Ready to be set up in the myQ
Solid Blue Connected to your mobile device. You are not yet connected to the Internet. If this
persists after setup, check your home router and Internet.
Flashing Blue and Green Connecting to Wi-Fi and connecting to the myQ
Solid Green Connected to the myQ
Flashing Purple Receiving firmware updates.
Solid Red Camera thermal error state when the camera reaches high heat 60 °C temperature
and cools down.
Tools:
• Philips Screwdriver
• Ladder
• Masking Tape (optional)
3.
Unscrew the
camera slowly
from the opener
housing.
TIP: Use
masking tape to
hold the camera
in place as you
remove screws.
6.
Align and
screw in
the new
camera into
the opener
housing.
9.
Locate the
notch in the
camera's
opener and
pull down.
Adjust the
camera
position as
needed.
11.
myQ SERIAL NUMBER
Find end panel
label on the side
1200 138 96C
of the GDO. Place
MAC ADDRESS
the new service
CC6A10382955
kit label onto the
PART DATE
050DCTB MC
location shown.
IC: 2666A–9612
FCC IC: HBW9612
CONTAINS
FCC ID: HEW9588
IC: 2666A–9588
Service kit label
FCC ID: MWB–0000AM2
IC: 2666A–GDOCAM2
App.
®
App.
®
App.
®
Model 041-0041
Masking
Tape
End panel label
01/21/22