Guarantee Conditions - VENSO EcoSolutions Grow Light Duo SE Manuel D'instructions

Guarantee conditions

Thank you for choosing an EcoSolutions product. These products are developed for us by Parus in
Korea. They are carefully tested and inspected to ensure correct function and operation.
Guarantee conditions
Your product is covered by a 2-year guarantee. The guarantee is valid from the date of purchase as
shown on your receipt. To make a guarantee claim, please contact the reseller from whom you purchased
the product.
Exception from the guarantee commitment
The guarantee will be invalided in any of the following events:
·
if the product has been connected to a dimmer
·
if the product has been connected to the wrong voltage or to a dimmer control device
·
if the product has been used outside the recommended temperature range
·
if the product has been subjected to mechanical damage, e.g. dropped on a concrete floor
·
if the product has been dismantled for troubleshooting/repairs
Read the user instructions before using the product. Save the instructions for future reference.
Safety instructions
Before using the light, read and follow these instructions:
·
The light is NOT intended for outdoor use
·
temperature range -20°C – +40°C
·
never install the light in a wet or moist luminaire
·
make sure your hands are dry during installation
·
never use the light in a sealed compartment; always allow air to circulate around it
·
do not connect the light to a dimmer
·
do not look directly at the light when it is on
·
take care when connecting the light to avoid electric shocks
·
the light's heat sinks will become hot (35–50°C) during use
·
All electrical installation work required to install the light must be performed by a qualified professional
·
do not use the light if it fails to light up, starts blinking or emits a weak light
·
In the event of malfunction, switch off the unit immediately. Never try to repair the light yourself, since
this could cause serious damage and invalidate the guarantee
General information
Many indoor plants come from parts of the world where the daytime hours and light conditions are very
different to our own. Growing indoors therefore places particularly high demands on the lighting. With
the right light source, you can grow herbs and plants indoors and additionally enhance comfort for us
humans.
Technical function
The product consists of a light source (LED) with wavelengths that are optimised to boost plants' health
and growth.
Installation and assembly
Assemble the product according to instructions on the next page. Connect the power supply to the device
and plug the power cord into an outlet or a timer. Use a timer to set the time, 12-16 hours for cultivation.
Placing the product
The product should be placed on a suitable location indoors with a temperature between 16 and 26
degrees. The ideal environment is a temperature of 18 - 24 degrees, with a humidity of 50% and good air
circulation.
Storage and maintenance
Store the light and packaging out of children's reach. The fixture has no replaceable parts.
Grow Light Duo
20W Plant luminaire
The Grow Light Duo plant luminaire is designed with full-spectrum light. This is a white LED light with a
predominance of blue and red wavelengths, encouraging optimal growth and photosynthesis. It is used for
seed starting and cultivation, or to provide extra light. The fixture emits a nice white light that fits well in a
home environment.
Seed starting
Sow your seeds in seed compost and let them sprout in the dark. After the seeds have sprouted, turn the
light on. Hang the luminaire at a height of 20 cm and raise it higher as the seedlings grow. You can combine
the luminaire with a timer set to 16 hours per day.
When the seedlings are about two months old, you can transplant them to a greenhouse or a garden plot.
Extra light
The Grow Light Duo plant luminaire can be used to provide extra indoor light for potted plants and herbs.
The luminaire should be combined with a timer so the plants can rest at night. Set the lighting time to
approximately 12 hours per day.
Assembly
Assemble the stand for the Grow Light Duo (included) as shown below.
1. First assemble two triangles with the metal rods A and B and the plastic couplings C and D.
2. Then assemble a stand using the two triangles and the remaining rod A.
3. Hang the fixture on the stand with the provided sususpension chains.
1
C
D
B
A
2 3
Technical specifications:
Model Grow Light Duo SE
Light angle 120°
Power output 20W
DimensionS WxLxH 46 x 600 x 19 mm
Voltage 100-240V
Rated current 1A
Operating voltage 25V
IP Certification IP 65
PPFD* (@100mm) 212 µmol
PPFD* (@200mm) 115 µmol
Luminous flux 1950 Lumen
Colour temperature 4 000K
Lifespan 30 000 h
*PPFD is a measure of photosynthetically available radiation.