Important Safety Instructions - NOMA 151-5596-2 Manuel D'instructions

3. Insert the middle section (B) of the tree into the bottom section (C) (Fig. 2). Insert the top section (A) into middle
section (B) (Fig. 3).
4. Insert the connector of the top section (A) into the end connector of the middle section (B), the connector of
the middle section (B) into the end connector of bottom section (C) and the connector of bottom section (C)
into the end connector of power cord in right direction properly and tightly according to the magnified
drawing on Fig. 4.
5. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure
that all wires are free of branch hinges (Fig. 5).
6. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one
along the centre of the main stem. Repeat pattern for each branch (Fig. 6).
7. Plug the well-connected power supply cord from the bottom section (C) into electrical outlet. This tree is
colour-changing: just press the button on the control box to change functions. The 4 lighting options
available are: all steady on white bulbs, all steady on multi-colour bulbs, continuous colour-changing
white to multi-colour and off.
TROUBLESHOOTING:
If any lights do not work on your pre-lighted tree, please check the following:
1. If entire tree or a section of the tree does not light:
a) Make sure the connectors of each section of the tree are well connected.
b) Check that there is power at the electrical outlet.
c) Check fuse in the plug of the power cord and replace if necessary (see Fuse Replacement below).
2. If a strand of lights still does not work:
a) Check that all bulbs are tightly fitted inside the sockets and that no bulbs are broken or missing.
Replace any broken or missing bulbs with replacement bulbs provided (see Bulb Replacement below).
If all bulbs are firmly in the sockets, slightly twist the bulbs from side to side to ensure proper connection.
b) If the lights still do not work, carefully remove each bulb one by one from the problem light string.
Pull the bulb AND plastic base straight out of the socket. Do not twist bulbs while removing from
sockets. Check the two wires at the bottom of the bulb holder. Each wire should be aligned properly
on the bulb holder to ensure a proper connection in the lamp socket. If one wire is missing or too short,
please replace bulb with a replacement bulb (provided).
CAUTION! - ALWAYS UNPLUG YOUR TREE FROM ITS POWER
SOURCE BEFORE ATTEMPTING EITHER FUSE OR BULB
REPLACEMENT.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical products basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
a)
b) Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When
products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting
(GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
c) This seasonal use product is not intended for permanent installation or use.
d) Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
e) Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
f) Do not let bulbs rest on the supply cord or on any wire.
g) Unplug the product when leaving the house, or when retiring for the night, or if leaving unattended.
h) This is not a toy. For decorative use only! To avoid risk of fire, burns, personal injury and electric shock it
should not be played with or placed where small children can reach it.
i) Do not use this product for other than its intended use.
j) Do not hang ornaments or other objects from cord, wire, or light string.
k) Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
l) Do not cover the product with cloth, paper, or any material not part of the product when in use.
m) This product is equipped with push-in type bulbs. Do not twist bulbs.
n) This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit
situation. If the fuse blows, unplug the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per the user servicing instructions
(follow product marking for proper fuse rating) and check the product. If the replacement fuse blows,
a short circuit may be present and the product should be discarded.
o) Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS
p)
All manuals and user guides at all-guides.com
,