1. Manuels
  2. Marques
  3. Nitro Manuels
  4. Nettoyants de piscine
  5. NC32
  6. Mode d'emploi

Nitro NC32 Mode D'emploi

Masquer les pouces
1
2
3
4
5
6
7

Publicité

Les langues disponibles

Les langues disponibles

Table des Matières

INSTALLATION
• Place the power supply in an area that will allow the cleaner to cover all areas of the pool.
• Be sure to only plug the power supply into a GFI (ground fault interrupter) or ELI (earth leak interrupter) protected electrical outlet.
• Look at the power supply and check that the power supply switch is in the off position.
• Plug the power supply into the protected outlet.
• Plug in the connector from the cleaner into the power supply. The connector is keyed so that it will only plug into the power supply one way.
Make sure that the plug is pushed all the way onto the power supply. Slide the connector lock (strain relief) onto the connector and turn
the connector lock clockwise until it is snug.
OPERATING THE CLEANER OUT OF THE WATER WILL DAMAGE THE MOTORS AND VOID THE WARRANTY
• Place the cleaner into the pool and if needed rock the cleaner side to side to release any trapped air. The cleaner will sink to the bottom of the pool.
• Put enough of the blue cord into the water to assure that the cleaner can easily reach all areas of the pool.
• Turn the switch on the power supply to the on position.
• The cleaner will begin its cleaning program.
• The cleaner will automatically shut itself down after two hours.
• If a second cleaning is required or the unit is accidentally shut off, you should wait one minute before switching the unit on again.
IMPORTANT NOTE: During normal operation, the cleaner will appear to shut off for a few seconds, raise the
front wheels off the pool bottom and move either left or right or turn for an undetermined amount of time. This is
normal and has been preprogrammed into the unit to assure the quickest and most efficient cleaning of your pool.
NITRO ROBOTIC POOL CLEANER OPERATION MANUAL
Congratulations on your purchase of the most technologically advanced automatic pool
vacuum available today. The Nitro is easy to use and will make maintaining your pool
affordable and effortless. Following these simple directions will insure that the Nitro will
quickly and efficiently clean your pool today and for many years to come.
DO NOT RUN THE CLEANER OUT OF THE WATER.

Publicité

Table des Matières
loading

Manuels Connexes pour Nitro NC32

Sommaire des Matières pour Nitro NC32

  • Page 1 NITRO ROBOTIC POOL CLEANER OPERATION MANUAL Congratulations on your purchase of the most technologically advanced automatic pool vacuum available today. The Nitro is easy to use and will make maintaining your pool affordable and effortless. Following these simple directions will insure that the Nitro will quickly and efficiently clean your pool today and for many years to come.

  • Page 2: Removing The Cleaner From The Pool

    “PUSH” and insert the filter bead into the channel, so In the course of using your Nitro, the cord may begin to coil. Excessive coiling • Slowly pull the blue cord to get the cleaner to the pool surface and near that the tabs are holding the bag in near the label with the word “PUSH”, as shown in...

  • Page 3: Troubleshooting Guide

    TROUBLE-SHOOTING GUIDE SYMPTOM POSSIBLE REASONS SOLUTIONS Drive motor has water in it Replace Drive motor UNIT GOING BACK AND FORTH ONLY A FEW FEET AT A TIME Debris stuck in drive wheel Remove debris Outlet not putting out proper voltage Check outlet voltage UNIT NOT FUNCTIONING Transformer not operating...

  • Page 4: Year L I M I T E D W A R R A N T Y

    Le Nitro est facile à utiliser et vous permet de nettoyer votre piscine à moindre coût et sans efforts. En suivant ce mode d'emploi simple, vous pourrez nettoyer votre piscine rapidement et de This warranty does not include replacements of the filter bag, bottoms lid, and brushes.
  • Page 5 à l'endroit où est inscrit « POUSSEZ » (push) sur le sac à filtre et insérez le bord Pendant l'utilisation du Nitro, il se peut que le cordon commence à s'enrouler. Des torsades • Tirez lentement sur le cordon bleu pour approcher le nettoyeur de la surface et du du filtre dans la rainure de façon à...

  • Page 6: Guide De Dépannage

    GUIDE DE DÉPANNAGE SYMPTÔME RAISONS POSSIBLES SOLUTIONS Il y a de l’eau dans le moteur d’entraînement Remplacez le moteur d’entraînement L’APPAREIL AVANCE ET RECULE SANS CESSE DE QUELQUES PIEDS SEULEMENT Des débris sont piégés dans la roue motrice Enlevez les débris La tension de la prise d’alimentation n’est pas correcte e Vérifiez la tension de la prise L’APPAREIL NE FONCTIONNE PAS...

  • Page 7: Nc32 Garantie Limitée De 12 Mois

    NC32 GARANTIE LIMITÉE DE 12 MOIS Ce produit a été fabriqué, testé et vérifié conformément aux exigences techniques particulières. Il est garanti contre les défauts matériels et les vices de fabrication dans des conditions normales d'utilisation, et il est soumis aux conditions et aux limitations décrites ci-dessous.

Table des Matières