Cleaning, Maintenance And Ordering Spare Parts - EINHELL TE-CD 18 Li E Mode D'emploi

6.3 Changeover switch (Fig. 3/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
screwdriver and for preventing the cordless
screwdriver from being switched on inadvertently.
You can select between clockwise and counter-
clockwise rotation. To avoid causing damage to
the gearing, the direction of rotation must only be
changed when the equipment is at a standstill.
When the slide switch is in the middle position,
the On/Off switch is blocked.
6.4 On/Off switch (Fig. 3/Item 4)
Infi nitely variable speed control is possible with
the On/Off switch. The further you push the
switch, the higher the speed of the cordless
screwdriver.
6.5 Switching from speed 1 to speed 2
(Fig. 2/Item 6)
You can work with a higher or lower speed
depending on the position of the selector switch.
Change the gear only when the drill is at a
standstill. If you fail to observe this point, the
gearing may be damaged.
6.6 Battery capacity indicator (Fig. 4 /Item 2)
Press the battery capacity indicator switch (11).
The battery capacity indicator (2) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive
discharge and is defective. Do not use or charge
a defective battery pack.
6.7 LED lamp (Fig. 4/Item 9)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
Anl_TE_CD_18_Li_E_SPK7_USA.indb 13 Anl_TE_CD_18_Li_E_SPK7_USA.indb 13
EN
6.8 Changing the bit (Fig. 5)
Caution! Set the changeover switch (3) to its
center position whenever you carry out any work
(for example changing the tool, maintenance
work, etc.) on the cordless screwdriver.
•
The cordless screwdriver is fitted with a
quick-action chuck (8) with an automatic
spindle stop.
•
Open the chuck (8). The chuck opening (10)
must be large enough to hold the tool (drill bit
or screwdriver bit).
•
Select the suitable tool. Push the tool as far
as possible into the chuck opening (10).
•
Tighten the chuck (8) and then check that the
tool is secure.
6.9 Screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw. Set the torque to suit the screw size as
specifi ed in the instructions.
7. Cleaning, maintenance and
ordering spare parts
HAZARD!
Always take the battery out of the equipment
before starting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it down with compressed air at
low pressure.
•
We recommend cleaning the equipment
immediately each time after use.
•
Clean the equipment regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may
be aggressive to the plastic parts in the
equipment. Ensure that no water can get into
the interior of the equipment. The ingress of
water into an electric power tool increases the
risk of an electric shock.
7.2 Maintenance
There are no other parts inside the equipment
which require maintenance.
- 13 -
02.05.2019 16:49:08 02.05.2019 16:49:08