Preparation For First Time Usage; Turn On The Unit For The First Time; Clock Set Up - Sylvania CDVC90DP Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Preparation for First Time Usage

Turn on the unit for the first
time
VCR
VCR
VCR
VCR
VCR
1
1
Turn on the TV and set it
to channel 3.
• If channel 3 is already occupied for broadcasting,
see"RF Output Channel" section.
2
2
POWER
TV Screen
LANGUAGE SELECT
B ENGLISH
FRANÇAIS
or
ESPAÑOL
3
3
AUTO SET UP
Do you connect the cable from the cable box or
the satellite box to the DVD/VCR's ANT IN jack?
YES
Y
es
Y
es
Press the MENU
button to exit
• Refer to "Tips for Cable Box
or Satellite Box" section on
page 6.
No
No
Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized
channel.
• You can select only the channels memo-
rized in this unit by using the CHANNEL
buttons.
• If "AUTO SET UP" appears on the TV
screen again, check the cable connections.
Then, press the
B button once again.
Tips
Tips
• Repeat these steps only if either there
was a power failure or this unit has been
unplugged for more than 30 seconds.
To Select a Channel
You can select a channel by directly
entering channel using the Number but-
tons on the remote control.
Notes for using the Number buttons:
• When selecting cable channels which
are higher than 99, enter channel
numbers as a three-digit number.(For
example: 117, press 1,1,7)
• You must precede single-digit channel
numbers with a zero (For example:
02, 03, 04 and so on).
All manuals and user guides at all-guides.com
To Preset the Channel Again
1) Press the MENU button until the main
menu appears.
2) Select "CHANNEL SET UP" by pressing
the K or L button. Then, press the B but-
ton.
3) Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button.
After scanning, the tuner stops on the low-
est memorized channel.
To Change the On-Screen Language
1) Press the MENU button until the main
menu appears.
2) Select "LANGUAGE SELECT" by press-
ing the K or L button. Then, press the B
button.
3) Select "ENGLISH" , "FRANÇAIS" or
[ON]
"ESPAÑOL" by pressing the K or L but-
ton. Then, press the CLEAR/C.RESET
button.
Tips
Tips
• If you accidentally select Spanish or
French and need English: Press the
MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press
the B button, and select ENGLISH. Finally,
CH 01
press the CLEAR/C.RESET button.

Clock Set Up

VCR
VCR
VCR
VCR
VCR
1
1
MENU
• If the clock is not set, the
or
NO
2
2
or
3
3
or
– 10 –
4
4
5
5
6
6
-MENU-
7
7
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE SELECT
AUDIO OUT
TV STEREO
[ON]
SAP
CLOCK SET screen
appears when you press
the MENU button. In this
case, go to step [2].
8
8
CLOCK SET
MONTH DAY
YEAR
0 3 / – –
– – – –
HOUR MINUTE
AM/PM
– – : – –
– –
Tips
Tips
Select the current month
• To go back one step, press the s button
(during the steps [2] to [7].)
• Your clock setting will be lost if either there
is a power failure or this unit has been
unplugged for more than 30 seconds.
CLOCK SET
MONTH DAY
YEAR
0 3 / 1 5
– – – –
HOUR MINUTE
AM/PM
– – : – –
– –
Select the current day
CLOCK SET
MONTH DAY
YEAR
0 3 / 1 5
2 0 0 4
or
HOUR MINUTE
AM/PM
– – : – –
– –
Select the current year
CLOCK SET
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
AM/PM
0 5 : – –
– –
Select the current hour
CLOCK SET
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
AM/PM
0 5 : 4 0
– –
Select the current minute
CLOCK SET
MONTH DAY
YEAR
0 3 / 1 5 MON 2 0 0 4
or
HOUR MINUTE
AM/PM
0 5 : 4 0
P M AM
B PM
Select "AM" or "PM"
To exit the CLOCK SET
screen.
EN

Publicité

Chapitres

Table des Matières
loading

Table des Matières