LumenRadio eXalux CONNECT RX100S Mode D'emploi

GENERAL INFORMATION
This instruction manual contains important notifications regarding
the safe use of the CONNECT RX100s.
Please take the time to read this manual carefully and thoroughly
before installing and operating the system.
We recommend you keep a copy for future use and you transfer it
to the buyer if you resell the system.
EXALUX reserves the right to modify and upgrade its range of
products, with no obligation to integrate these changes into
products already sold. Therefore, all the information found in this
manual is subject to change without notice.
OVERVIEW
(1) Power USB connector
(2) Power indicator
(3) Status indicators
(4) Signal quality indicators
(5) XLR5 Connector, DMX OUT
(6) Unlink button
OPERATING PRINCIPLE
The CONNECT RX100s is a wireless DMX receiver, that uses
LumenRadio CRMX technology (2.4GHz). This system allows
the users to control DMX enabled fixtures wirelessly, several tens
meters away.
CONNECT RX100s can receive an entire DMX universe (512
channels) without any latency.
A complete system is composed of a CONNECT TX100 transmitter,
linked with one or several CONNECT RX100 or RX100s receivers,
and can be controlled from a standard DMX controller.
Several CONNECT TX100 + CONNECT RX100s can be used
simultaneously, in order to transmit several DMX universes.
POWER SUPPLY
The CONNECT RX100s is powered from the micro USB connector
(1), located at the bottom of the case.
Use a standard USB cable to connect the RX100s to a Powerbank
or USB charger.
When powered, the indicator (2) turns on.
DMX OUTPUT
All manuals and user guides at all-guides.com
The DMX signal received form the radio-transmitter is outputed on
the XLR5 (5), with the standard pinout :
Pin1: GND | Pin2: DMX- | Pin3: DMX+
Connect all the DMX fixtures to control on this DMX output.
The indicator DMX (3) turns on when a DMX signal is received and
outputed on the XLR5.
LINKING WITH TRANSMITTER
By default, CONNECT RX100s do no listen to the data sent by the
transmitter CONNECT TX100: it is necessary to link the receivers to
the transmitter.
In order to link a CONNECT RX100s to a CONNECT TX100, follow
this procedure:
- Make sure both devices are powered.
- Start the linking procedure by pressing the dedicated button
on the CONNECT TX100.
- During the linking period (10s), any unlinked CONNECT RX100s
in range will automatically link to the CONNECT TX100.
If a CONNECT RX100s is linked to a transmitter, the Link (3)
indicators turns on (even if the transmitter is off).
Several receivers CONNECT RX100s can be linked during a single
procedure.
During the linking procedure, the DMX signal is not transmitted.
UNLINKING RECEIVERS
At any moment, it is possible to reset the configuration of the
CONNECT RX100s, by unlinking the transmitter.
To do so, press the button (6) during 3 seconds, until the Link (3)
indicator turns off.
The CONNECT RX100s can then be linked to any transmitter.
RADIO
A four-level gauge (4) provides a feedback on the radio signal
strength.
In order to optimize the radio communication, it is recommanded
to install the transmitters and receivers in open spaces, without
large metalic objects.
It is also recommanded to place the antennas as described in the
following image.
LUMENRADIO COMPATIBILITY
EXALUX recommands the use of the transmitters CONNECT
TX100. Nevertheless, the CONNECT RX100s can be used with any
transmitter compatible with CRMX Technology from LumenRadio.
For more information, refer to www.lumenradio.com.
SAFETY INSTRUCTIONS
Proper use:
This unit is designed to control lighting sources using DMX
commands. Use the device only in its intended use as described in
this manual. Any other use, as well as use in other conditions, will be
considered non-compliant and can cause injury and damage. No
liability will be assumed for damages resulting from improper use.
The device should only be used by people in full possession of
their physical, sensory and mental abilities who must have the
knowledge and experience required. All the other persons are only
allowed to use the device under the supervision or direction of a
person responsible for their safety.
Safety:
Risk of electric shock
This system requires high voltage, which can result in an electrical
shock. Never remove covers. The parts inside the device are
maintenance free.
Dangers for children
Ensure a proper disposal of plastic envelopes and packaging.
They should not be near babies nor young children: suffocation
danger. Make sure that children do not remove small parts of the
unit (e.g. knobs, screws or similar). Children could swallow the
pieces and choke. Never leave unattended children use electrical
devices.
Electric shock caused by a short circuit
Do not modify the power cord nor the plug. In case of non-
compliance, there is a risk of electric shock and fire hazard and
death. If in doubt, contact a certified technician.
Risk of fire
Never cover the device nor its ventilation slots. Do not install the
device close to a source of heat. Keep the device away from flames.
Terms of use
The device is designed for indoor use. To prevent damage, do
not expose the product to liquid or moisture. Avoid direct sunlight,
clogging and strong vibrations.
Power supply
Check the operation of the power supply before connecting to
the system.
Before connecting the appliance, check if the voltage indicated
on the device matches the voltage on the local supply network
and if the socket is fitted with a differential circuit breaker. In case
of non-compliance, the device could be damaged and the user
might be injured.
When a storm is announced or the unit must not be used for an
long time, unplug it to reduce the risk of electric shock or fire.
CARE
– Unplug the unit when cleaning it and during all maintenance
operations.
– Do not use cleaning product: use a dry cloth and rub gently.
– Store the device in a clean, dry place, away from direct
exposure from sunlight and dust.