How To Run A Wash Cycle Or A Drying Cycle - Hotpoint AQUALTIS AQD1071D 69 Manuel

How to run a wash cycle or a
drying cycle
WARNING: before you use the Washer-dryer for the first time,
EN
run a wash cycle with detergent and no laundry, using the 90°
cottons cycle without pre-wash.
1. SWITCH THE MACHINE ON. Press the
the indicator lights will illuminate for 1 second and the text
AQUALTIS will appear on the display; the indicator light
corresponding to the
manner and the START/PAUSE indicator light will flash.
2. SELECT THE PROGRAMME. Turn the PROGRAMME
KNOB left or right, until the required programme has been
selected; the name of the programme will appear on the
display. A temperature and spin speed is set for each
programme; these may be adjusted. The cycle duration will
also appear on the display.
3. LOAD THE LAUNDRY. Open the porthole door. Load the
laundry, making sure you do not exceed the maximum load value
indicated in the table of wash cycles on the following page.
4. MEASURE OUT THE DETERGENT. Pull out the detergent
dispenser drawer and pour the detergent into the relevant
compartments as described in "Description of the machine".
5. CLOSE THE PORTHOLE DOOR.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons on the control panel:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum temperature
and spin speed values set for the selected cycle, or the most
recently-used settings if they are compatible with the selected
cycle. The temperature can be decreased by pressing the
button, until the cold wash "OFF" setting is reached. The
spin speed may be progressively reduced by pressing the
button, until it is completely excluded "OFF". If these buttons
are pressed again, the maximum values are restored.
! Exception: if the
temperature can be increased up to a value of 90°C.
Setting the drying cycle.
The first time the button
automatically select the maximum drying cycle which is
compatible with the selected wash cycle. Subsequent presses
will decrease the drying level and then the drying time, until
the cycle is excluded completely ("OFF"). If these buttons are
pressed again, the maximum values are restored.
Drying may be set as follows:
A - Based on a set time period: between 20 and 180 minutes.
B- Based on the desired laundry dryness level:
Iron: suitable for clothes which will need ironing afterwards.
the remaining dampness softens creases, making them
easier to remove.
Hanger: ideal for clothes which do not need to be dried fully.
Cupboard: suitable for laundry which can be put back in a
cupboard without being ironed.
Extra: suitable for garments which need to be dried
completely, such as sponges and bathrobes.
If your laundry load to be washed and dried is much greater
than the maximum stated load, perform the wash cycle,
and when the cycle is complete, divide the garments into
groups and put some of them back in the drum. At this
point, follow the instructions provided for a "Drying only"
cycle. Repeat this procedure for the remainder of the load.
A cooling-down period is always added to the end of each
drying cycle.
8
All manuals and user guides at all-guides.com
button. All
button will then remain lit in a constant
programme is selected, the
is pressed, the machine will
Drying only
Use the cycle selector knob to select a drying cycle ( - - )
in accordance with the type of fabric. The desired drying level or
time may also be set using the DRYING button
Setting a delayed start.
To set a delayed start for the selected cycle, press the
corresponding button repeatedly until the required delay period has
been reached. During the setting procedure, the delay period and
the text "Starts in:" will be displayed, along with the flashing
symbol. After the delayed start has been set, the
will remain fixed on the display, which will also indicate the
duration of the selected cycle with the text "Ends in:" and the
cycle duration. Press the DELAYED START button just once to
display the delay time set previously. After the countdown has
begun, the display will show the text "Starts in:" and the delay
period. Once the set delay time has elapsed, the machine will
begin its cycle and the display will show "Ends in:" and the time
remaining until the end of the cycle. To remove the delayed start
option, press the button until the display shows the text OFF;
the symbol will disappear.
Modify the cycle settings.
• Press the button to activate the option; the name
of the option will then appear on the display and the
corresponding indicator light will illuminate.
• Press the button again to deactivate the option; the
name of the option will then appear on the display
followed by the text OFF, and the corresponding
indicator light will switch off.
! If the selected option is not compatible with the selected
wash cycle, this incompatibility will be signalled by the
flashing of the indicator light and a sound alert
(3 beeps); the option will not be activated.
! If the selected option is not compatible with another
option that has been selected previously, the indicator light
corresponding to the first option selected will flash and
only the second option will be activated; the indicator light
corresponding to the button will remain lit in a constant manner.
! The options may affect the recommended load value and/
or the duration of the cycle.
7. START THE PROGRAMME. Press the START/PAUSE
button. The corresponding indicator light remains lit in a fixed
manner and the porthole door locks (the
light illuminates). The icons corresponding to the wash cycle
phases will light up during the cycle to indicate which phase
is currently in progress. To change a wash cycle once it has
already started, pause the Washer-dryer by pressing the
START/PAUSE button; then select the desired cycle and
press the START/PAUSE button again. To open the door
during a wash cycle, press the START/PAUSE button; if the
LOCK indicator light is switched off you may open the
door. Press the START/PAUSE button again to restart the
wash cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This is indicated by
the illuminated text END. The porthole door may be opened
immediately. If the START/PAUSE indicator light is flashing,
press the button to end the cycle. Open the door, unload
the laundry and switch off the machine.
! If you wish to cancel a cycle which has already begun, press
and hold the button until the cycle stops and the machine
switches off.
.
symbol
LOCK indicator