Campbell Hausfeld PN001000 Manuel page 3

Operating Instructions
Important Safety Instructions
(Continued)
TOOL USE AND CARE
a. Use clamps or another practical way
to secure and support the workpiece
to a stable platform. Holding the
work by hand or against the body is
unstable and is able to lead to loss
of control.
b. Do not force the tool. Use the
correct tool for the application. The
correct tool will do the job better
and safer at the rate for which the
tool is designed.
c. Do not use the tool if the switch
does not turn the tool on or off. Any
tool that cannot be controlled with
the switch is dangerous and must be
repaired.
Never attach air line
while the nailer is
loaded as the immediate valve resetting
that may occur may forcefully eject the
nail. First connect air line, then load.
d.
Disconnect the
tool from the air
source before making adjustments,
doing tool maintenance,
clearing jams, leaving work
area, or unloading the tool.
precautionary measures reduce the
risk of injury to persons.
e. Store the tool when it is idle out
of reach of children and other
untrained persons. A tool is
dangerous in the hands of untrained
users.
f. Maintain the tool with care. Keep
a cutting tool sharp and clean. A
properly maintained tool, with sharp
cutting edges reduces the risk of
binding and is easier to control.
g. Check for misalignment or binding
of moving parts, breakage of parts,
and any other condition that affects
the tool's operation. If damaged,
have the tool serviced before using.
Many accidents are caused by poorly
maintained tools. There is a risk of
bursting if the tool is damaged.
h. Use only those fasteners listed
in the Accessories section of this
manual. Fasteners not identified
for use with this tool by the tool
manufacturer are able to result in
a risk of injury to persons or tool
damage when used in this tool.
i. Selecting an appropriate tool
actuation system, taking into
consideration the work application
for which the tool is used.
or other flammable liquids
to clean the tool. Never use
the tool in the presence of
flammable liquids or gases. Vapors
could ignite by a spark and cause an
explosion which will result in death or
serious personal injury.
remove, tamper with,
or otherwise cause the
trigger lock or trigger
to become inoperable.
Do not operate any
tool which has been modified in a like
fashion. Death or serious personal
injury could result.
Always disconnect
the tool from the
power source
when unattended,
performing any maintenance or repair,
clearing a jam, or moving the tool to a
new location.
Such
Always fit tool with a
fitting or hose coupling
on or near the tool in
such a manner that all
compressed air in the tool is discharged
at the time the fitting or hose coupling
is disconnected. Do not use a check
valve or any other fitting which allows
air to remain in the tool. Death or
serious personal injury could occur.
hands or any other body
parts in the fastener
discharge area of the tool.
The tool might eject a fastener and
could result in death or serious personal
injury.
Never carry the
tool by the air hose
or pull the hose to
move the tool or a
compressor. Keep
hoses away from
heat, oil and sharp
edges. Replace any
hose that is damaged, weak or worn.
Personal injury or tool damage could
occur.
fasteners. Respect the tool as a working
implement; no horseplay. Always keep
others at a safe distance from the work
area in case of accidental discharge of
Never use
fasteners. Do not point the tool toward
gasoline
yourself or anyone whether it contains
fasteners or not. Accidental triggering
of the tool could result in death or
serious personal injury.
drive a fastener on top
of other fasteners. The
Do
fastener could glance
not
and cause death or a
serious puncture wound.
Do not operate or allow
anyone else to operate
the tool if any warnings
or warning labels are not legible.
Warnings or warning labels are located
on the tool magazine and body.
Dropping or throwing the tool can
result in damage that will make the tool
unusable or unsafe. If the tool has been
dropped or thrown, examine the tool
closely for bent, cracked or broken parts
and air leaks. STOP and repair before
using or serious injury could occur.
magazine is empty. Accelerated wear on
the tool may occur.
and fittings before connecting the
tool to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may be
reduced.
Never
place
3
PN001000
Always assume the
tool contains
Do
not
WARNING
!
Do not drop or
throw the tool.
Avoid using the
tool when the
Clean and check all
air supply hoses
www.chpower.com