Power Tool Safety Rules; Work Area; Electrical Safety; Personal Safety - Dremel DIGITAL High 398 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

!
Read and understand all instructions. Failure to follow all instructions listed below, may
WARNING
result in electric shock, fire and/or serious personal injury.

Work Area

Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep by-standers, children, and visitors away while
operating a power tool. Distractions can cause you
to lose control.

Electrical Safety

Double Insulated tools are equipped with a polarized
plug (one blade is wider than the other.) This plug
will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it
still does not fit, contact a qualified electrician to
install a polarized outlet. Do not change the plug in
any way. Double Insulation
the three wire grounded power cord and grounded
power supply system. Before plugging in the tool, be
certain the outlet voltage supplied is within the voltage
marked on the nameplate. Do not use "AC only" rated
tools with a DC power supply.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is
grounded. If operating the power tool in damp
locations is unavoidable, a Ground Fault Circuit
Interrupter must be used to supply the power to your
tool. Electrician's rubber gloves and footwear will
further enhance your personal safety.
Don't expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
Do not abuse the cord. Never use the cord to carry
the tools or pull the plug from an outlet. Keep cord
away from heat, oil, sharp edges or moving parts.
Replace damaged cords immediately. Damaged
cords increase the risk of electric shock.
When operating a power tool outside, use an
outdoor extension cord marked "W-A" or "W." These
cords are rated for outdoor use and reduce the risk of
electric shock. Refer to "Recommended sizes of
Extension Cords" in the Accessory section of this
manual.

Power Tool Safety Rules

SAVE THESE INSTRUCTIONS
eliminates the need for

Personal Safety

Stay alert, watch what you are doing and use
common sense when operating a power tool. Do not
use tool while tired or under the influence of drugs,
alcohol, or medication. A moment of inattention
while operating power tools may result in serious
personal injury.
Dress properly. Do not wear loose clothing or
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
Keep handles dry, clean and free from oil and grease.
Avoid accidental starting. Be sure switch is "OFF"
before plugging in. Carrying tools with your finger on
the switch or plugging in tools that have the switch
"ON" invites accidents.
Remove adjusting keys or wrenches before turning
the tool "ON". A wrench or a key that is left attached
to a rotating part of the tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables
better control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate
conditions.
Tool Use and Care
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable
and may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it "ON" or
"OFF". Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
Store idle tools out of reach of children and other
untrained persons. Tools are dangerous in the hands
of untrained users.
Page 2

Publicité

Table des Matières
loading

Produits Connexes pour Dremel DIGITAL High 398

Table des Matières