Eagletone MH512 5in1 Guide De L'utilisateur page 6

User's guide
Eagletone MH512 5in1
TABLE OF CONTENTS
1. Safety instructions
2. Technical specifications
3. Installation
4. How to set up the unit
5. How to control the unit
6. DMX 512 configuration
7. DMX 512 connections
8. Troubleshooting
9. Fixture cleaning
1. SAFETY INSTRUCTIONS
Please read the instructions care-
fully as they include important
information about the installation
operation and maintenance.
Please keep this user manual for
future reference. If you sell the fixture
to another user, be sure that they also
receive this instruction booklet.
Unpack and check carefully that there
is no transportation damage before
using the fixture.
It is important to ground the yellow/
green conductor to earth in order to
avoid electric shock.
Disconnect mains power before servi-
cing and maintenance.
Maximum ambient temperature is:
40°C. Do not use the unit in places
where the temperature is higher than
this.
In the event of a serious operating
problem, stop using the fixture imme-
diately. Never try to repair the fixture
by yourself. Repairs carried out by
unskilled people can lead to damage or
malfunction. Please contact the nearest
authorized technical assistance center.
Always use spare parts of the same
type.
2
All manuals and user guides at all-guides.com
Do not connect the device to any
dimmer pack.
Do not touch any wire during operation
as there might be a hazard of electric
shock.
To prevent or reduce the risk of elec-
trical shock or fire, do not expose the
fixture to rain or moisture.
The housing must be replaced if it is
visibly damaged.
Do not look directly into the LED light
beam while the fixture is on.
There are no user serviceable parts
inside the fixture. Do not open the
housing or attempt any repairs by
yourself. In the unlikely event your
fixture may require service, please
contact your nearest dealer.
Due to the magnifying type lens, please
keep it out of direct sunlight. This can
cause heat to build up inside the unit,
which will seriously damage it.
2. TECHNICAL SPECIFICATIONS
Features 5 high-power 15W RGBWY
5-in-1 LEDs.
Each color of R, G, B, W, Y can be
controlled individually.
DMX 5/14 switchable channels.
Smooth 0~100% dimming and variable
strobe speeds.
Three operation modes:
DMX. Master/Slave mode.
Sound-activated mode.
Ideal for discotheques, clubs, bars,
parties, Mobile DJs, etc.
Input voltage: AC100V~240V 50/60Hz
Power consumption: 80W
Fuse: T 3A
Dimensions: 240×230×300mm
Weight: 4kg
3. INSTALLATION
The unit should be mounted via its screw
holes on the bracket. Always ensure that
the unit is firmly fixed to avoid vibration
and slipping while operating. Always
ensure that the structure to which you are
attaching the unit is secure and is able
to support a load of 10 times the unit's
weight. Also always use a safety cable
that can hold 12 times the unit's weight
when installing the fixture.
The equipment must be attached by
professionals, and in a place which is out
of people's reach and where no one has to
pass by or under it.
User's guide
Eagletone MH512 5in1
4. HOW TO SET UP THE UNIT
4.1 Rear Panel
INPUT OUTPUT
Display
Shows the various menus and the
selected functions
MODE/ESC
Allows to select the programming
functions
UP
Allows to go forward in the selected
functions
DOWN
Allows to go backward in the selected
functions.
ENTER
Allows to confirm the selected functions
Mains input
Connect to mains power supply.
DMX input
For DMX512 link, use a 3/5-pin XLR plug
cable to input DMX signal.
DMX output
For DMX512 link, use a 3/5-pin XLR plug
cable to link to the next unit.
3