Knape & Vogt WUSC12-1-35 Mode D'emploi

Parts Included
A. Waste Bin(s)
B. Sliding Base Assembly (1)
C. Waste Bin Chassis (1)
D. Lid(s) (if supplied)
E. Extension Brackets (2)
F. #6 x 5/8" Mounting Screws
for Door (8 = 4 + 4 extra)
G. #8 x 1" Mounting Screws
for Sliding Assembly (8 = 6 + 2 extra)
H. #10 - 24" x 1/4" Mounting Screws (4)
for Extension Brackets
A
B
C D
E
G
F
Tools Required
• Phillips head screwdriver
• Drill with 1/16" (1.5mm) bit for
drilling pilot holes
• Tape measure or ruler
• Pencil
• Scissors
Product Assemblies
• WUSC12-1-35PT • WUSC12-1-50WH
• WUSC12-1-35WH • WUSC12-2-27PT
• WUSC15-2-35PT • WUSC12-2-27WH
• WUSC15-2-35WH • WUSC18-2-50PT
• WUSC12-1-50PT • WUSC18-2-50WH
2700 Oak Industrial Drive NE , Grand Rapids, MI 49505 USA
800.253.1561 • 616.459.3311 • www.kv.com
SOFT-CLOSE UNDERMOUNT WASTE BIN
Inspect all parts and read all instructions prior to beginning assembly and installation.
1. Install Sliding Base Assembly
A. Place sliding base assembly on cabinet floor in the center of the cabinet opening. Refer to chart
(Fig. 1) to determine set back. Position the front edge of the front mounting strap at the
designated set back.
B. Once the position is determined, fasten the sliding base assembly to the cabinet floor by using
4 - #8 x 1" mounting screws through the interior holes. (Fig. 2) Tighten with a screwdriver.
C. Place 2 -#8 x 1" mounting screws through the exterior holes (Fig. 3) and fasten with a Phillips
head screwdriver until the head of the screw is flush with the sliding base assembly.
DO NOT OVER TIGHTEN, as this can warp the slide.
2. Remove Door
With drill or screwdriver, remove door hinges from cabinet and door.
IMPORTANT: Door must be removed prior to waste bin chassis installation.
3. Install Waste Bin Chassis
A. Lower and insert rear of chassis so that the channels on the chassis fit onto the slides on the
sliding base assembly. Push chassis toward the back of the cabinet until it sits against the back
of the slides and you hear a "click." (Fig. 5) The chassis is now fully seated and locked. Grasp the
door mount brakets, slowly pull the chassis out of the cabinet until it stops moving. Both slides
should fully extend.
NOTE: If your slides do not fully extend, your chassis is not seated properly. To correct, push
the drawer slide forward until it locks into position.
Fig. 1
SKU #
WUSC12-1-35
H
WUSC12-1-50
WUSC12-2-27
WUSC15-2-35
WUSC18-2-50
Fig. 2
©2013 Knape & Vogt. All rights reserved. Made in USA. Knape & Vogt
OVERLAY CABINET
Extension
Cabinet Bracket
Opening Set Back Orientation
11.5-12
14.5-15 2.375
11.5-12
14.5-15 2.375
11.5-12
14.5-15 2.375
14.5-15
17.5-18 2.375
17.5-18 2.375
Fig. 3
See
Chart
reserves the right to change specifications without notice.
®
INSET CABINET
Set Back
In 2.125" + door thickness
Out 2.375" + door thickness
In 2.125" + door thickness
Out 2.375" + door thickness
In 2.125" + door thickness
Out 2.375" + door thickness
In 2.125" + door thickness
Out 2.375" + door thickness
Out 2.375" + door thickness
Fig. 5
DO NOT OVER
TIGHTEN
Extension
Bracket
Orientation
Not Used
Out
Not Used
Out
Not Used
Out
Not Used
Out
Out
310384-A-0913