Primex OneVue Sync Guide D'installation Rapide

Sync Bluetooth
STEP 1 WHAT YOU NEED TO KNOW BEFORE YOU BEGIN
INSTALL ORDER:
Sync devices must be installed in a
specific order (1) bridge devices first, (2) then
clocks and/or repeaters. Do not attempt to set
clocks by bringing them to a bridge or another
clock. Clocks must work at install location.
NETWORK FIREWALL:
Must allow outbound connections and file downloads from OneVue URLs:
console.primexonevue.com
deviceapi-alt.primexonevue.com
deviceapi.primexonevue.com
onevueapi.primexonevue.com
us-east-1-production.s3.amazonaws.com
Bridge connection to a switch port:
Spanning tree portfast (STP) must be enabled when a switch port is not
connected to other routers or switches. Optionally STP can be turned off,
which is not the same as disable.
FIRST POWER-ON OPERATION:
Bridge enters 8-hour deployment mode: Bluetooth Network automatically builds
at the 20th and 50th minute of each hour. After each build, a bridge automatically
checks-in to OneVue to send Bluetooth clock data. Clock/repeater add a clock
mode: searches for Sync Bluetooth mesh network continuously for 8 hours.
REPEATER:
Located to address coverage gaps to allow clocks to form communication path
to nearest bridge.
STEP 3 INSTALL CLOCKS & REPEATERS
1. Is bridge in 8-hour deployment mode? If yes, continue on. If not,
first power-cycle the bridge.
2. Begin installing clocks and/or repeater closest to the bridge and
work outward in a logical manner. Devices must be first powered on
at their install location.
3. Do not wait for a clock to set its time; continue installing clocks
and return for a quick visual check later.
4. Remove Bluetooth ID tear-off label and place on floor plan/paper to
identify device install location.
POSSIBLE REPEATER LOCATIONS
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Primex, Inc. is under license. Other trademarks and trade names are those of their respective owners. OneVue is a trademark of Primex, Inc. The innovative technology software solution for facility and time synchronization monitoring and reporting. All other trademarks are the property of their respective owners.
©2020 Primex, Inc. The Primex logo is a registered trademark of Primex, Inc. All Rights Reserved. 6.20
Quick Install Guide
®
1. 2.
STEP 2 INSTALL BRIDGE
1. MOUNT
• Away from metal racks and other obstructions
• 5 feet or higher above floor
• Near corridor side of room, preferably near a door
• Do not mount above ceiling
2. APPLY POWER & VERIFY NETWORK CONNECTION
Power-On (check-in) Sequence
1 - powered on
2 - connected to network
3 - connected to NTP Server
4 - connected to OneVue
HOW TO POWER-CYCLE BRIDGE
(8-HOUR DEPLOYMENT MODE)
1. Remove PoE or AC power
2. Remove batteries
3. Wait 10 seconds
4. Reapply power: batteries first, then PoE or AC-power. Be sure
battery power switch is in UP position for battery backup.
STEP 4 UPDATE DEVICE NAME IN ONEVUE
1. For each Sync Bluetooth device, locate its 12-character Bluetooth ID > update its
Name to its install location.
NOTE: A bridge adds clocks and repeaters to OneVue. If bridge is in 8-hour
deployment mode and devices connect to the mesh network, devices are added at
20 and 50 past the hour. It can take from 24 hours to 7 days for a clock or repeater
to be added to OneVue.
SYNC
Connection Successful
• BtON
• Signal OK
• Green LED solid
APPLY POWER NOTE:
Insert backup battery.
Located to the lower-right of
the battery compartment, set
the battery on/off switch to
the Up (On) position.
141186 10/19