Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
Roller stand for magnifier lamp
Item no. 1526047
Intended use
This product serves as a movable carrier for a suitable magnifying lamp. The maximum
permissible weight of the magnifying lamp is 3.3 kg.
For safety reasons, you must not rebuild and/or modify this product. Using the product for
purposes other than those described above may damage the product. Improper use may also
result in safety hazards for the user. Read the instructions carefully and store them in a safe
place. Make this product available to third parties only together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Package contents
• 5x legs
• Middle section
• Base cover
• Column
• Washer
Up-to-date operating instructions
Download the latest operating instructions at www.conrad.com/downloads or scan the QR code
on this page. Follow the instructions on the website.
Explanation of symbols
This symbol is used to highlight important information in these operating instructions.
Always read this information carefully.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorized use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Always handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Also observe the safety and operating instructions for the magnifying lamp.
• Check the contents of the packaging before assembling the product. You will not
be able to assemble the product unless all components are present.
• Proceed with care when assembling and mounting the product! This product has
some sharp edges which have the potential to cause injury!
• Only carry out the work necessary to mount the product. Never perform any
conversion or repair work. Do not make changes to the product.
• Do not overload the product. Refer to the technical data for information on the
load capacity.
• Place the product only on a flat, sturdy surface only.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
• Spring washer
• Cylinder head screw
• Hex key
• Operating instructions
Assembly
• Insert the legs (2) from below into the middle section (3).
• Insert the column (1) into the round hole of the middle section.
• Replace the base cover (4) on the bottom of the middle section.
• First place the spring washer (6) and then the washer (5) onto the cylinder head screw (7).
• Insert the cylinder head screw from below onto the base cover.
• Firmly tighten the cylinder head screw with the hex key (8).
• Now you can insert the foot of a suitable magnifying lamp into the top of the column.
Maintenance and cleaning
• Remove the magnifying lamp before you clean the product.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
Always dispose of the product according to the relevant statutory regulations.
Technical data
Load capacity ............................... max. 3.3 kg
Operating conditions ..................... -5 to +40 °C, <95 % RH
Storage conditions ........................ -10 to +50 °C, <95 % RH
Dimensions (Ø x H) ...................... 620 x 715 mm
Weight .......................................... 7 kg
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
1
2
3
4
5
6
7
8
*1526047_V1_0317_02_IPL_m_en
Publicité
