Publicité
Instruction Manual
P I C T U R E F R A M I N G
FITTING TOOL
U.S. Patent No. 6,896,168
Rev. 7/08
Identification
Lock Plate
Foot
Bumper
Turret
Preparation
A. Fill frame
1. Turn over frame.
Fig. 1
2. Load glass, matboard and image and
backing material into frame (Fig. 1).
B. Choose an insert (Fig. 2).
1. Flexible Insert- Bendable insert used
in photo frames where material can
Moulding
easily be changed.
Brad Nails - Economical insert.
Can be used for securing canvas.
Multipoint Insert - Bendable insert
and used to hold fillets in place.
Rigid Insert - Firm insert used in
permanent applications.
continued on next page
Preparation continued
B. Choose an insert (continued)
2. Rotate turret so insert choice faces
Fig. 3
foot (Fig. 3).
C. Determine insert spacing and quantity
1. Corner spacing is generally 1" (3cm)
to 2" (5cm) from corner.
2. Side spacing is generally 4" (10cm)
to 5" (13cm) apart (Fig. 4).
Model F400-1
www.logangraphic.com
Description
The Model F400-1 Fitting Tool has been
designed to provide long lasting quality opera-
tion with easy to use features. It's primary
purpose is to drive pins, points and nails into
wood picture frame moulding to securely hold
framing materials in place. The Model F400-1
Fitting Tool features a unique and revolution-
ary rotating turret to accommodate all of the
most popular style points.
Reference Part No. L988
Lever - Moveable handle which drive inserts.
Foot - Sliding stop block.
Lever
Lock Plate - Locks foot secure.
Turret - Insert holder which rotates. Holds four
insert styles.
Flexible Insert - Bendable insert used to hold
framing material inside frame.
Insert
Backing Material
(Foamboard or Cardboard)
Matboard or image
Glass
Fig. 2
Brad
Multipoint
Rigid
Flexible
Nail
Insert
Insert
Insert
Fig. 4
Operation
A. Driving Insert
1. Slide foot away from turret.
2. Load insert into turret slot. Be sure
point end faces out (Fig. 5).
3. Align body and tip of insert against
frame. Rest body on framing materi-
al. Slide foot until bumper rests firm-
ly against frame (Fig. 6).
1
4. Firmly squeeze handle and drive insert into the wood until turret stops
against frame (Fig. 7).
Note-for best results keep body flat on material while squeezing.
5. Squeeze lock plate on foot and rotate foot to release (Fig. 8).
6. Slide body back along top of framing material to remove from insert. Do
not lift up, but rather pull straight back.
7. Repeat to finish.
2
Trouble Shooting
Problem:
Points bend when being inserted.
Solution:
Try using a different insert more suited to hardwood.
Make sure the turret is resting flush on back material being framed.
Problem:
Mats or framed material buckles after being secured.
Solution:
Let the turret rest gently on back of material when inserting points.
Do not angle inserts down to "pinch" material being secured.
Problem:
Fitting Tool handle does not release after point insertion.
Solution:
Release pressure by squeezing lock plate on the foot and swivel foot
to clear moulding, then withdraw turret in opposite direction of insertion.
3
Instruction Manual
L969
L811
L972
L964-N
L978
L977
L970
L967
L963
L975
Rev. 7/08
Fig. 5
Model F400-1
Fig. 7
Warranty
Logan Graphic Products, Inc. ("Logan") warrants the Fitting Tool -
Model F400-1, to be free from defects in parts and workmanship for a
period of one year from the date of original purchase. Logan warrants
that it will either repair or replace, at it's sole discretion, any neces-
sary replacement parts found to be defective. Should the product
need to be returned to Logan for repair or replacement parts, authori-
zation for any return must come from Logan in writing. Costs of
returning the product to Logan, including insurances, shall be borne
by the purchaser. Logan shall not be liable for any damages or losses,
incidental or consequential, direct or indirect, arising from the use of
this product. This warranty extends only to the original purchaser and
is not assignable or transferable. This warranty is in lieu of all other
warranties, expressed or implied.
Model F400-1
FITTING TOOL
No.
Description
L811
Lock Plate Spring
L966
L963
Bumper
L964-N
End Cap
L965
Handle
L966
Body
L967
Turret-Top
L968
Turret-Bottom
L965
L969
Lock Plate
L970
Foot
L972
Drive Rod
L976
L975
Turret Screw
L968
L976
Pivot Screw
L977
Ball
L978
Ball Spring
1100 Brown Street, Wauconda, IL 60084 USA
Phone 1 847 526 5515 Toll Free 1 800 331 6232
4
Fig. 6
5
Fig. 8
6
7
Qty.
1
1
1
1
1
1
1
1
1
1
4
1
1
1
Logan Graphic Products, Inc.
www.logangraphic.com
Reference Part No. L988
Publicité
