Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION INSTRUCTIONS - SLING
Mounting of Sling Fixture
1.
Open the Back Box by loosening the Locking Screw.
2.
Verify and remove only necessary Gasket material where Back Box will mount.
3.
Knock-out Back Box material for necessary mounting location.
4.
Mount Back Box to Junction Box securely, using hardware supplied by others.
5.
Connect electrical connections with fixture wiring.
6.
Seal Back Box to Housing by pushing on front of Housing while tightening Locking
Screw to ensure that screw is fully seated in the Housing Recess. Ensure wiring
remains within Back Box and wires do not get pinched.
7.
Apply Caulk or other Sealant (supplied by others) around the top and both sides of
the Back Box where it meets the mounting surface.
Mounting of Sling Fixture with Knuckle Accessory
1.
Open the Back Box by loosening the Locking Screw.
2.
Mount Knuckle Plate to mounting locations of Back Box using #8-32x5/16" screws.
3.
Route electrical leads from Back Box through Knuckle Plate and Knuckle. In order to
complete routing through Knuckle, may need to use Phillips head screwdriver to
remove screw at middle of the Knuckle. Make sure to reconnect Knuckle parts once
wire routing is complete.
4.
Connect electrical connections with fixture wiring routed through the Knuckle.
5.
Mount Knuckle on desired mounting location, using sealing compound to seal
Knuckle threads on mounting location.
6.
Seal Back Box to Housing by pushing on front of Housing while tightening Locking
Screw to ensure that screw is fully seated in the Housing Recess. Ensure wiring
remains within Back Box and wires do not get pinched.
7.
If light output angle needs to be adjusted, loosen screw on middle of the Knuckle to
allow rotation of Knuckle for fixture to desired light output angle. Tighten screw once
desired light output angle is achieved.
Mounting of Sling Fixture with Yoke Accessory
1.
Open the Back Box by loosening the Locking Screw.
2.
Mount Yoke Plate to mounting locations of Back Box using #8-32x5/16" Screws.
3.
Connect Strain Relief through Back Box and Yoke Plate. Ensure gasket covers hole
in Back Box.
4.
Route SO Cord through Strain Relief into the Back Box. Twist Strain Relief to tightly
secure SO Cord.
5.
Connect SO Cord connections with fixture wiring inside the Back Box.
6.
Seal Back Box to Housing by pushing on front of Housing while tightening Locking
Screw to ensure that screw is fully seated in the Housing Recess. Ensure wiring
remains within Back Box and wires do not get pinched.
7.
Make electrical connections with SO Cord, ensuring SO cord is routed through
Wireway Hole on Yoke.
8.
Mount Yoke on desired mounting location, ensuring SO cord with electrical power
connections is contained inside mounting surface (Junction Box for example). Be sure
to allow for some excess SO Cord outside mounting surface in order to rotate fixture
into desired location.
9.
If light output angle needs to be adjusted, loosen screw on Yoke Mounting Bracket
to allow rotation of Yoke for fixture to desired light output angle. Tighten screw once
desired light output angle is achieved.
GROUND TO
BACK BOX
GROUND
GROUND TO
HOUSING COVER
GROUND
BUILDING
CONNECTION
LINE
NEUT
NOTES:
For replacement LEDs and Drivers, please contact Hubbell Lighting for any replacement parts.
Contact your local distributor or agent to confirm parts availability prior to ordering replacement parts.
701 Millennium Boulevard Greenville, SC 29607 (864) 678-1000
All manuals and user guides at all-guides.com
SAVE THESE INSTRUCTIONS
SURGE
PHOTOCELL
OPTIONAL FEATURE.
USE CAP TO DEACTIVATE.
CHECK DRIVER
CHECK DRIVER
GROUND TO
HOUSING COVER
IF PRESENT
Back Box with Gasket
Locking Screw
Housing Recess
Knuckle Screw to Allow Rotation
Yoke Screw to Allow Rotation
DIM +
VIOLET
DIM -
GRAY
- INPUT -
-OUTPUT -
LINE
LED +
SEE TABLE
AC LED DRIVER
LED -
SEE TABLE
NEUT
GND
WIRING DIAGRAM
SHEET 2 OF 2
Photocell (Use Cap to Deactivate)
Housing
Housing
Housing
Yoke Mounting Bracket
Wireway Hole
RED
LED COB
BLACK
RED
LED COB
BLACK
RED
LED COB
BLACK
www.hubbelloutdoor.com
Back Box
Knuckle Plate
Back Box
Yoke Plate
Publicité
