REED Bevel Boss CPBDK Manuel D'instructions

REED Bevel Boss™ Cordless Pipe Bevelers (CPB) are
designed for use with a cordless die grinder to bevel the
outside diameter and/or inside diameter of plastic pipe. The
CPBDADP and CPBMADP beveler adapters are designed for
use ONLY with a DeWalt
Assembly instructions are provided in this document.
REED CPBDK kit is complete with beveler attachment with
exterior shroud, Router Bit RBIT1, die grinder, DeWalt®
battery and charger in a storage case. The CPBDBT base
tool with beveler attachment and die grinder requires a
router bit and DeWalt
for assembly of bit into beveler. Many users already own the
battery and are able to use it on this REED tool.
ASSEMBLY DIAGRAM 1
NOTE: Internal shroud CPBIDS #94644 must used for
beveling the inside diameters and is available as an
accessory.
SHROUD
PERSONAL SAFETY
GUIDE PLATE
1. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating
power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing and gloves
JUSTING KNOB
T BE LOCATED
away from moving parts. Loose clothes, jewelry, or long
FROM SWITCH
AS SHOWN hair can be caught in moving parts.
3. Always wear eye protection.
MILWAUKEE GRINDER
OPERATING INSTRUCTIONS:
MODEL #2784-20
This tool is to be used on plastic pipe only. To adjust depth
of chamfer, loosen the adjusting knob and slide the guide
plate up or down until the required amount of the router bit
is exposed above the guide plate and tighten the adjusting
knob. To the left side of the Adjusting Knob there are four
engraved lines on Adapter with 1/8" increments. When
using the RBIT1 bit with the Adjusting Ring all the way to the
bottom, the beveler will cut a 5/8" long bevel. By lining up
the bottom of the Adjusting Ring with the engraved line, the
length of the bevel is reduced by 1/8" for each line.
If the grinder is capable of multiple speeds, set the
grinder to the fastest setting. Turn on grinder and place
guide plate flat against the end of pipe. Slowly bring the
router bit against edge of pipe until the bearing at the end
of the bit is contacting the pipe. Slowly rotate the beveler
counterclockwise for an OD bevel and clockwise for an ID
bevel, being sure to keep the bearing in contact with pipe.
A second quick pass around the pipe may be needed if the
1425 West 8th St.
Bevel Boss™ Cordless Pipe Beveler Instructions
CPBDK, CPBDBT, CPBDKE, CPBDADP, CPBMADP
/ Milwaukee cordless die grinder.
® ®
® battery. Refer to these instructions
GUIDE PLATE
SHOULD BE FLUSH
WITH BOTTOM OF
ROUTER BIT
CLAMP SCREW
MILWAUKEE
ADAPTER
P.O. Box 1321, Erie, PA 16512 USA
Adapting to DeWalt
APPLIES TO: 04658, 04659, 04666, 04648, 04649
bevel is not smooth. An uneven bevel can happen if the
guide plate is not kept perpendicular to the pipe and the
bearing on the router bit is not kept against the pipe.
OPERATING INSTRUCTIONS RBIT2
(1" BIT) ONLY:
The RBIT2 (1" bit) removes a large amount of material.
Therefore, it is STRONGLY RECOMMENDED when cutting
a ¾" to 1" depth bevel to make two passes around the pipe,
removing half of the material with each pass. For the first
pass set the Adjusting Ring so it lines up with the engraved
line to the right of the Adjusting Screw and make the first
pass around the pipe. To complete the bevel, readjust the
Adjusting Ring to remove the remainder of the material.
OPERATING DIAGRAM
4 REFERENCE LINES
1/8" INCREMENTS
FOR ADJUSTING
THE BEVEL SIZE
REED CPBDADP fits DeWalt
XR Lithium-Ion Cordless Brushless Variable Speed Die
Grinder
REED CPBMADP fits Milwaukee
2784-22 M18 FUEL™ 18V Lithi
Cordless 1/4 in. Die Grinder
DeWalt ® and Milwaukee
Reed Manufacturing.
REED MANUFACTURING
Phone: 800-666-3691 or +1-814-452-3691
www.reedmfgco.com
®
and Milwaukee
ASSEMBLY DIAGRAM 2
5/32"
APPROXIMATE
OPERATING DIAGRAM
1/8"
®
model DCG426B 20V MAX
®
models 2784 20 and
um-Ion Brushless
® are registered trademarks that are not associated with
reedsales@reedmfgco.com
®
Die Grinders
LOCATE ROUTER BIT SO
THE UNFINISHED AREA ON
THE SHAFT IS JUST ABOVE
RBIT1
TOP OF COLLET
COLLET
RBIT2
RECOMMENDED:
SET HEIGHT TO THIS LINE
FOR REMOVING HALF THE
MATERIAL FOR FIRST PASS
ON LARGER BEVEL
WHEN USING RBIT2
1
0422-54654