Kettler Power Stepper Instructions De Montage page 3

Sie deren richtigen Sitz. Drehen Sie die selbstsichernden Muttern
bis zum spürbaren Widerstand zuerst mit der Hand auf, ansch-
ließend ziehen Sie sie gegen den Widerstand (Klemmsicherung)
mit einem Schraubenschlüssel richtig fest. Kontrollieren Sie alle
Schraubverbindungen nach dem Montageschritt auf festen Sitz.
Achtung: wieder gelöste Sicherheitsmuttern werden unbrauchbar
(Zerstörung der Klemmsicherung) und sind durch Neue zu ersetzen.
GB Assembly Instructions
Study these instructions carefully before assembling and ucing the equipment. The lnstructions contain important information
for your safety and for the use and maintenance of the "Power Stepper". Keep the instructions in a safe place for your
own information, for maintenance work and ordering spare parts.
For Your Safety
The "Power Stepper" should be used only for its intended purpose,
i.e. for physical exercise by adult persons.
Any other use of the equipment is prohibited and may be dan-
gerous. The manufacturer cannot be held liable for damage or
injury caused by improper use of the equipment.
The rowing machine has been designed in accordance with the
latest standards of safety. Any features which may have been a
possible cause of injury have been avoided or made as safe as
possible.
The unit complies with the DIN EN 957 - 1/8 class H. It is the-
refore unsuitable for therapeutic use.
Incorrect repairs and structural modifications (e.g. removal or repla-
cement of original parts) may endanger the safety of the user.
Handling the equipment
Before using the equipment for exercise, check carefully to ensure
that it has been correctly assembled.
Do not set the equipment up in rooms which are frequently used
or close to doors, entries etc.
It is not recommended to use or store the apparatus in a damp
room as this may cause it to rust. Please ensure that no part of
the machine comes in contact with liquids (drinks, perspiration
etc.). This may cause corrosion.
The "Power Stepper" must be set up on an even impact-resistant
base. To absorb the vibrations, lay a straw or rubber mat under
the machine.
The product is designed for use by adults and children should not
be allowed to play with it. Children at play behave unpredictably
and dangerous situations may occur for which the manufacturer
cannot be held liable. If, in spite of this, children are allowed to
use the equipment, ensure that they are instructed in its proper
use and supervised accordingly.
On principle, the equipment does not require any special main-
tenance. All bearings are pre-lubricated (further lubrication is not
required) and require little maintenance.
Instructions for Assembly
Ensure that you have received all the parts required (see check
list) and that they are undamaged. Should you have any cause
for complaint, please contact your KETTLER dealer.
Before assembling the equipment, study the drawings carefully
and carry out the operations in the order shown by the diagrams.
The correct sequence is given in capital letters.
Bewahren Sie die Originalverpackung des Gerätes gut auf,
damit sie später u. U. als Transportverpackung verwendet werden
kann.
Aus fertigungstechnischen Gründen behalten wir uns die
Vormontage von Bauteilen (z.B. Rohrstopfen) vor.
Damaged components may endanger your safety or reduce the
lifetime of the equipment. For this reason, worn or damaged parts
should be replaced immediately and the equipment taken out of
use until this has been done. Use only original Kettler spare
parts.
In case of enquiry, please contact your Kettler dealer.
If the equipment is in regular use, check all its components
thoroughly every 1 – 2 months. Pay particular attention to the
tightness of bolts and nuts.
Instruct persons using the equipment (in particular children) on
possible sources of danger during exercising.
Before beginning your program of exercise, consult your doctor
to ensure that you are fit enough to use the equipment. Base your
program of exercise on the advice given by your doctor. Incorrect
or excessive exercise may damage your health.
After a longer period of disuse, the hydraulic absorbers may not
achieve their best performance at once. Before beginning exer-
cising or after a period of disuse, it is recommended to activate
the absorbers by several pumping movements.
Do not use corrosive or abrasive materials to clean the equipment.
Ensure that such materials are not allowed to pollute the envi-
ronment.
To operate correctly, the pulse function requires a minimum
voltage of 2,7 volts.
Please ensure that liquids or perspiration never enter the machine
or the electronics.
Before use, always check all screws and plug-in connections as
well as respective safety devices fit correctly.
When training intensivly shock absorbers may become very hot.
Please avoid contact and do not touch the shock absorbers after
training.
Please note that there is always a danger of injury when working
with tools or doing manual work. Therefore please be careful when
assembling this machine.
Ensure that your working area is free of possible sources of
danger, for example don't leave any tools lying around. Always
dispose packaging material in such a way that it may not cause
3