KEUCO Royal Match 12804 171351 Instructions De Utilisation page 3

US
Read all instructions before using or installing this product.
Technical data
– Maximal load each shelf:
– Supply voltage:
– Required electrical outlet:
– Max. power consumption:
Prod. No.:
- 12804 171351:
- 12805 171351:
Maximal load mirror cabinet total:
- 12804 171351:
- 12805 171351:
– Degree of protection:
– Ambient conditions:
Operating temperature
Storage temperature
– Luminous color
Mounting dimensions, see page 8.
CAUTION: Risk of personal injury: This
product is very heavy. Get assistance lifting the
cabinet.
Before installation check whether the fastening mate-
rials included are suitable for the anchoring base. The
fastening materials are suitable exclusively for stud walls
with timber constructions or for drywall constructions
with timber wood reinforcement.
Installation, see fi gure 1 onwards on page 9.
• Mark the wall bracket position, see fi gure 1.
• Prepare the safety locking, see fi gure 2.
• Mount the wall brackets and safety locking to the
wall, see fi gure 3.
WARNING - GROUNDING
INSTRUCTIONS
This product must be connected to a grounded me-
tal, permanent wiring system, or an equiment-groun-
ding conductor must be run with the circuit con-
ductors and connected to the equipment-grounding
terminal or lead on the product.
Wiring diagram, see fi gure 4 on page 10.
• Connect the mirror cabinet to the power supply,
see fi gure 5a/5b.
• Hang the mirror cabinet on the wall from above,
see fi gure 6.
• Fix the mirror cabinet to the wall by turning the
screw of the safety locking counterclockwise, see
fi gure 7 on page 11.
• Place the glass shelf holders in the mirror cabinet,
see fi gure 8.
max 3.3 lb
120 V AC / 50/60 Hz
15 A / 1800 VA
Width Weight Light
47-1/4" 76.06 lb 30 W
51-3/16" 82.01 lb 30 W
115.74 lb
121.69 lb
NEMA 1
32° – 113° F
-40° – 158° F
3000 Kelvin
• Place the glass shelves in the mirror cabinet,
see fi gure 9.
• Observe the maximum load on the glass shelves
(3.3 lb), see fi gure 10.
• Adjust the doors of the mirror cabinet, see fi gure 11
on page 12. Unscrew the screw and pull off cover. Ad-
justment by using the two screws. After fi xing screws
remount cover.
• Set the opening resistance of the doors,
see fi gure 12. Turn set screw clockwise to make the
door more sluggishly or counterclockwise to make the
door smoother.
Operation
Button functions
Button Function
Light on/off
• Pressing the button switches the mirror cab-
inet on with the selected settings. The white
LED goes off.
• Pressing the button again switches the mirror
cabinet off. The white LED lights up.
• The white LED can be deactivated.
– Switch on the mirror cabinet.
– Press and hold the button for 15 seconds.
- The lighting gets lighter or darker.
- The lighting switches off briefl y and the
white LED is deactivated.
To switch the white LED back on, repeat the
described procedure.
Dimming the lighting
• Press the button when the mirror cabinet is
switched on and hold until the desired bright-
ness or the end value has been reached.
The setting is stored and reproduced when
switched on again.
Replacement parts with order numbers, see page 15.
The light sources may only be replaced by the
manufacturer, its customer service or by an
equally qualifi ed person.
For information about warranty and mainte-
nance, see the enclosed Care Instructions
and Warranty Card.
Disposal instructions
This category of device does not belong in
the domestic waste, but must be disposed of
separately in accordance with the relevant
local national regulations.
3