Publicité
Les langues disponibles
Les langues disponibles
Components
Power "On" Light (amber): This light will illumi-
nate when the unit is plugged into the 230V~
wall outlet and will remain on until the unit is
unplugged.
CAUTION: Read the instructions for "Filling the
Water Tank" before opening the Safety Cap.
Always depress hand grip steam trigger until
all pressure/ steam has been vented from
boiler.
CAUTION: Always unplug before filling.
IMPORTANT: Do NOT add cleaning solutions,
scented perfumes, oils or any other chemicals
to the water used in this appliance. Use tap
water or distilled/purified water if the tap water
in your area is very hard.
Filling Your SC 50
With Water
IMPORTANT: Always insure that the unit is
"UNPLUGGED" from the wall receptacle prior
to initial filling or re-filling the water tank. Failure
to follow these steps will cause the water tank
to overfill.
Step 1:
Before filling the SC 50, make sure that
the unit is NOT plugged in.
Step 2:
Turn Safety/Filler Cap counter
clockwise until removed. (See cau-
tion above.)
Step 3:
Place Water Filling Funnel in tank and
add 780 cc of water Do not overfill.
Replace Safety/Filler Cap by turning
clockwise. Heating time is approxi-
mately 3-5 minutes with cold water.
Filling boiler with hot water will shorten
heat up time.
Step 4:
Plug the unit into a standard 230volt
(3-prong) grounded wall receptacle.
The power light will illuminate.
Step 5:
Allow approximately 3-5 minutes for
vapor to reach its working tempera-
ture and
pressure.
Step 6:
Connect desired attachments onto
the Flexible Steam Hose.
Step 7:
Upon initial use, some water will come
out from the nozzle of the attach-
ment. This is unheated water in the
hose and is normal.
OPERATING INSTRUCTIONS
CAUTION: Always drain condensate from
hose before use or if unit has been left idle for
a period of time. To drain hose, direct nozzle
into an appropriate container or sink and de-
press hand grip steam trigger. Once hose has
been drained, normal use may be resumed.
Never direct nozzle towards people, animals
or plants.
IMPORTANT: When the SC 50 has run out of
water, steam output will cease.
CAUTION: Allow unit to cool for 5 minutes be-
fore refilling. When refilling the machine while it
is still hot, the first drops of water might bubble
up. Use caution when opening the Safety/Filler
Cap as cap may become hot during use and
escaping steam
Refilling Your SC 50 With Water
Step 1:
Step 2:
Step 3:
CAUTION: Allow unit to cool for 5 minutes befo-
re refilling. If the SC 50 is still hot, there is a risk
that water will be squirted back during filling
and cause scalding. Extreme care should be
taken when refilling the unit. Use caution when
opening the Safety/Filler Cap as cap may
become hot during use and escaping steam
can cause scalding.
Step 4:
Step 5:
Step 6:
Step 7:
18
can cause scalding.
Disconnect Electrical Power Cord
from wall outlet.
Depress and hold the hand grip
steam trigger to ensure that any
remaining pressure in the boiler has
been released.
Carefully loosen the safety/filler cap
by turning counter clockwise. Any
residual steam will be released below
the safety/filler cap if the tank has not
been completely vented. When the
hissing stops and the last of the steam
has been released, remove the filler
cap. Allow unit to cool down.
Allow the vapor steam cleaner to
cool for 5 minutes before re-filling with
water.
Refill water tank with water using the
filling funnel.
Firmly screw the safety/filler cap back
onto the unit by turning clockwise.
Connect power cord to the wall
outlet.
Publicité
