Astro Pneumatic Tool EUROHVT1 Manuel D'instruction

WARNING
Study, understand and follow all instructions provided with this product.
Read these instructions carefully before installing, operating, servicing
or repairing this tool. Keep these instructions in a safe accessible place.
Intended Use of the Tool
The Astro EuroPro Spray Guns are designed to spray the following
solvent and waterborne light to medium viscosity materials:
Enamels, lacquers, polyurethane, urethane top coats, urethane
basecoat, urethane clearcoat and all primers. Materials which are
acidic, abrasive and/or contain benzene must not be used. In order
to achieve the best results, surface and paint preparation must be
completed in accordance with paint manufacturer's instructions and
recommendations. The Astro EuroPro Guns are intended to be used
only by professionally trained individuals. Strict compliance of
applicable local and national regulations must be followed.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using this
product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in damages
and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and Bystanders).
• Never use this tool for any application other than for which
it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with accessories
not designed for it could result in serious injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
EUROPRO FORGED HVLP TOUCH UP GUN
WITH 1.0MM NOZZLE & PLASTIC CUP
EUROHVT1
MADE IN TAIWAN
EUROPRO FORGED HVLP TOUCH UP GUN
WITH 1.0MM NOZZLE & PLASTIC CUP
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to charge
back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor should direct the original user
to return the product (with the exceptions listed below) with the distributor's name,
address, adequate proof of date of purchase or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro will
replace free of charge component parts of this product that fail within 1 year of first
use by the original user. Items included in this category include but are not limited
to kits, hand tool kits and any other product where there are multiple items or
components that make up the unit. Please contact the phone number below in
order to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and may
not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including warranties
of merchantability and fitness for a particular purpose. Some states do not allow the
exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
When unpacking, check the parts diagram and part number
listing on page 3 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
DURABLE & LIGHTWEIGHT
• Forged body provides longer tool life
• Anodized body for corrosion protection
• Internal coated passages
• Stainless steel needle and fluid tip
• Slick finish for faster & easier cleaning
• Lightweight: 285 grams (0.6 Lbs)
HIGH EFFICIENCY
• Unique pattern designed for great coverage, optimal overlapping
• Low overspray (bounce back)
• Great transfer efficiency
• Superior atomization
• Innovative, advanced HVLP technology
QUICK THREAD TECHNOLOGY
• 1.5 Turn to lock/unlock the air cap
• 3 Turns to lock/unlock the fluid nozzle
• 4 Turns to lock/unlock the fluid cup
• Wide threads for easy cleaning
• M11*P1.5 female thread fluid joint
• Compatible with most traditional and disposable cup systems
SMOOTH OPERATION
• Soft trigger pull to reduce fatigue
• Precise lubricated adjustment knobs for better control
• Innovative CNC machining to avoid the need for gaskets behind the fluid tip
SPECIFICATIONS:
Nozzle Size:
Cup Capacity:
Operation Pressure:
Weight:
Gun Dimensions W x H:
Avg. Air Consumption:
Air Inlet Thread NPT:
Required Compressor:
Max. Pattern at 2" to 4-3/4" Distance:
Air Cap Output:
Air Hose I.D. Size:
DO NOT DISCARD – GIVE TO USER
Page 1
www.astrotools.com
Unpacking
1.0mm
250ml
29psi
0.6lbs. (285g)
5-3/4" x 4-3/8" (145mm x 110mm)
3-4.5cfm
1/4"
0.75-1.5hp
4" to 6" (100-150mm)
10psi
6-8mm