Tyco Security Products DSC PowerSeries PC5208 Instructions D'installation

PC5208 v1.0 Installation Instructions
8 Low Current Output Module
This installation sheet shall be used in conjunction with the Installation Manual (P/N: 29008247) of the
DSC equipment to which the PC5208 is connected (e.g. alarm controller, power supply, etc.).
The PC5208 module can be used to add up to 8 low-current programmable outputs to the compatible
DSC Alarm Controllers, models PC5015, PC1864, PC1832 and PC1616.
General
This product meets the requirements of Class II, Grade 2 equipment as per EN50131-1:2006+A1:2009,
EN50131-3:2009 Type A Standard.
Specifications
• Temperature range: -10°C to + 55°C (0°C to + 49°C for US and Canada)
• Relative Humidity: 93% non condensing
• Input ratings: 12V /700mA (provided by the alarm controller or separate limited power supply)
DC
• Board current draw: 50mA (set and unset state/alarm and non-alarm state)
• Board dimensions: 45mm x 92mm
• AUX output ratings: 12V , -15%/ +15% when Input voltage is between 85% to110% of rated value
DC
and output current is between 0mA - 250mA max. (in addition to 400mA for PGM)
• PGM outputs: Open collector, switched to ground, 50mA max
• Resettable fuse (PTC) used on circuit board instead of replaceable fuses. There are no serviceable
parts
Terminal Descriptions
TAM - This can be used to tamper the cabinet in which the PC5208 is mounted. Connect a normally
closed (NC) switch across TAM and BLK. If the tamper is not being used connect a piece of wire across
TAM and BLK to remove the trouble condition.
NOTE: There is a built-in tamper switch on the expander module located in the top left corner of
the circuit board. If the cabinet used to mount the PC5208 Output Module has the hardware
required to depress this tamper switch then DO NOT connect anything to the TAM terminal.
+AUX+ - There are two terminals for AUX power to provide easier wiring. These terminals are used to
provide power for devices. Maximum current draw is not to exceed 250 mA. Connect the positive lead of
powered devices to either AUX+ and the negative to the proper output terminal (O1 to O8).
KEYBUS - The 4 wire KEYBUS connection is used by the panel to communicate with the module. Con-
nect the RED, BLK, YEL and GRN terminals to the KEYBUS terminals on the main control.
O1 to O8 - Wire the positive lead of the device to either AUX terminal and the negative lead to the
required output terminal (O1 to O8). The following are examples of how to wire various devices to the
outputs:
Enclosures
The PC5208 may be installed within the same metallic cabinet as the alarm controller/power supply
(model Power UC1, PC5003C) or in a separate enclosure (model PC4003C). Internal and/or external
wiring for this module shall be routed, supported, clamped or secured in a manner that reduces the like-
lihood of: excessive strain on wire and on terminal connections; loosening of terminal connections; and
damage of conductor insulation.
The PC5208 can be installed in the metal enclosures listed below. Tamper protection switches can be
installed on all enclosures, including door opening protection and/or removal from the mounting posi-
tion. Doors can be secured using screws or keylock.
• Model PC5003C (removable door) made of 22Ga steel, painted, dimensions: 248mm(L) x
298mm(W) x 76mm(H), weight: 1500g.
• Model PC5003C (hinged door) made of 1.2mm thick steel, painted, dimensions: 248mm(L) x
298mm(W) x 76mm(H), weight: 2500g
• Model Power UC1 made of 18Ga steel, painted, dimensions: 315mm(L) x 319mm(W) x 100mm(H),
weight: 3150g.
• Model PC4003C made of 18Ga steel, painted, dimensions: 230mm(L) x 180mm(W) x 75mm(D),
weight 1050g.
NOTE: The Model PC5208 Output Module has been certified by Telefication according to
EN50131-1:2006 + A1:2009 for Grade 2, Class II when installed in the PC5003C (removable
door) enclosure.
LIMITED WARRANTY
Digital Security Controls (DSC) warrants that for a period of twelve months from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty, DSC shall, at its option,
repair or replace the defective equipment upon return of the equipment to its factory. This warranty applies only to defects in parts and
workmanship and not to damage incurred in shipping or handling, or damage due to causes beyond the control of DSC such as light-
ning, excessive voltage, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the
equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties, whether
expressed or implied and of all other obligations or liabilities on the part of DSC. This warranty contains the entire warranty. Digital
Security Controls neither assumes responsibility for, nor authorizes any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or liability concerning this product. In no event shall DSC be liable for any
direct or indirect or consequential damages, loss of anticipated profits, loss of time or any other losses incurred by the buyer in connec-
tion with the purchase, installation or operation or failure of this product.
Warning: Digital Security Controls recommends that the entire system be completely tested on a regular basis. However, despite fre-
quent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible for this product to fail to per-
form as expected.
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by DSC could void your authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance with the manufac-
turer's instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits
for Class B device in accordance with the specifications in Subpart "B" of Part 15 of FCC Rules, which are designed to provide reason-
able protection against such interference in any residential installation. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause interference to television or radio reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Re-orient the receiving antenna
• Relocate the alarm control with respect to the receiver
• Move the alarm control away from the receiver
• Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The user may
find the following booklet prepared by the FCC useful: "How to Identify and Resolve Radio/Television Interference Problems". This
booklet is available from the U.S. Government Printing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
IMPORTANT - READ CAREFULLY: DSC SOFTWARE PURCHASED WITH OR WITHOUT PRODUCTS AND COM-
PONENTS IS COPYRIGHTED AND IS PURCHASED UNDER THE FOLLOWING LICENSE TERMS:
This End-User License Agreement ("EULA") is a legal agreement between You (the company, individual or entity who acquired the Software and any
related Hardware) and Digital Security Controls, a division of Tyco Safety Products Canada Ltd. ("DSC"), the manufacturer of the integrated security
systems and the developer of the software and any related products or components ("HARDWARE") which You acquired. If the DSC software prod-
uct ("SOFTWARE PRODUCT" or "SOFTWARE") is intended to be accompanied by HARDWARE, and is NOT accompanied by new HARDWARE, You
may not use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT includes computer software, and may include associated media,
printed materials, and "online" or electronic documentation. Any software provided along with the SOFTWARE PRODUCT that is associated with a
separate end-user license agreement is licensed to You under the terms of that license agreement.
By installing, copying, downloading, storing, accessing or otherwise using the SOFTWARE PRODUCT, You agree unconditionally to be bound by the
terms of this EULA, even if this EULA is deemed to be a modification of any previous arrangement or contract. If You do not agree to the terms of this
EULA, DSC is unwilling to license the SOFTWARE PRODUCT to You, and You have no right to use it.
SOFTWARE PRODUCT LICENSE
The SOFTWARE PRODUCT is protected by copyright laws and international copyright treaties, as well as other intellectual property laws and treaties.
The SOFTWARE PRODUCT is licensed, not sold.
1. GRANT OF LICENSE This EULA grants You the following rights:
(a) Software Installation and Use - For each license You acquire, You may have only one copy of the SOFTWARE PRODUCT installed.
(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed, accessed, displayed, run, shared or used concurrently on or from differ-
ent computers, including a workstation, terminal or other digital electronic device ("Device"). In other words, if You have several workstations, You
will have to acquire a license for each workstation where the SOFTWARE will be used.
(c) Backup Copy - You may make back-up copies of the SOFTWARE PRODUCT, but You may only have one copy per license installed at any given
time. You may use the back-up copy solely for archival purposes. Except as expressly provided in this EULA, You may not otherwise make copies of
the SOFTWARE PRODUCT, including the printed materials accompanying the SOFTWARE.
2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS
(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not reverse engineer, decompile, or disassemble the SOFT-
WARE PRODUCT, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation. You may
not make any changes or modifications to the Software, without the written permission of an officer of DSC. You may not remove any proprietary
notices, marks or labels from the Software Product. You shall institute reasonable measures to ensure compliance with the terms and conditions of
this EULA.
(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single product. Its component parts may not be separated for use on
more than one HARDWARE unit.
(c) Single INTEGRATED PRODUCT - If You acquired this SOFTWARE with HARDWARE, then the SOFTWARE PRODUCT is licensed with the HARD-
WARE as a single integrated product. In this case, the SOFTWARE PRODUCT may only be used with the HARDWARE as set forth in this EULA.
(d) Rental - You may not rent, lease or lend the SOFTWARE PRODUCT. You may not make it available to others or post it on a server or web site.
(e) Software Product Transfer - You may transfer all of Your rights under this EULA only as part of a permanent sale or transfer of the HARDWARE,
provided You retain no copies, You transfer all of the SOFTWARE PRODUCT (including all component parts, the media and printed materials, any
upgrades and this EULA), and provided the recipient agrees to the terms of this EULA. If the SOFTWARE PRODUCT is an upgrade, any transfer must
also include all prior versions of the SOFTWARE PRODUCT.
(f) Termination - Without prejudice to any other rights, DSC may terminate this EULA if You fail to comply with the terms and conditions of this
EULA. In such event, You must destroy all copies of the SOFTWARE PRODUCT and all of its component parts.
(g) Trademarks - This EULA does not grant You any rights in connection with any trademarks or service marks of DSC or its suppliers.
3. COPYRIGHT - All title and intellectual property rights in and to the SOFTWARE PRODUCT (including but not limited to any images, photographs,
and text incorporated into the SOFTWARE PRODUCT), the accompanying printed materials, and any copies of the SOFTWARE PRODUCT, are owned
by DSC or its suppliers. You may not copy the printed materials accompanying the SOFTWARE PRODUCT. All title and intellectual property rights in
and to the content which may be accessed through use of the SOFTWARE PRODUCT are the property of the respective content owner and may be
protected by applicable copyright or other intellectual property laws and treaties. This EULA grants You no rights to use such content. All rights not
expressly granted under this EULA are reserved by DSC and its suppliers.
4. EXPORT RESTRICTIONS - You agree that You will not export or re-export the SOFTWARE PRODUCT to any country, person, or entity subject to
Canadian export restrictions.
5. CHOICE OF LAW - This Software License Agreement is governed by the laws of the Province of Ontario, Canada.
6. ARBITRATION - All disputes arising in connection with this Agreement shall be determined by final and binding arbitration in accordance with the
Arbitration Act, and the parties agree to be bound by the arbitrator's decision. The place of arbitration shall be Toronto, Canada, and the language of
the arbitration shall be English.
7. LIMITED WARRANTY
(a) NO WARRANTY - DSC PROVIDES THE SOFTWARE "AS IS" WITHOUT WARRANTY. DSC DOES NOT WARRANT THAT THE SOFTWARE WILL
MEET YOUR REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE.
(b) CHANGES IN OPERATING ENVIRONMENT - DSC shall not be responsible for problems caused by changes in the operating characteristics of
the HARDWARE, or for problems in the interaction of the SOFTWARE PRODUCT with non-DSC-SOFTWARE or HARDWARE PRODUCTS.
(c) LIMITATION OF LIABILITY; WARRANTY REFLECTS ALLOCATION OF RISK - IN ANY EVENT, IF ANY STATUTE IMPLIES WARRANTIES OR CONDI-
TIONS NOT STATED IN THIS LICENSE AGREEMENT, DSC'S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE
LIMITED TO THE GREATER OF THE AMOUNT ACTUALLY PAID BY YOU TO LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS
(CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCI-
DENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
(d) DISCLAIMER OF WARRANTIES - THIS WARRANTY CONTAINS THE ENTIRE WARRANTY AND SHALL BE IN LIEU OF ANY AND ALL OTHER WAR-
RANTIES, WHETHER EXPRESSED OR IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE) AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO OTHER WARRANTIES. DSC NEITHER
ASSUMES NOR AUTHORIZES ANY OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFY OR TO CHANGE THIS WARRANTY, NOR TO
ASSUME FOR IT ANY OTHER WARRANTY OR LIABILITY CONCERNING THIS SOFTWARE PRODUCT.
(e) EXCLUSIVE REMEDY AND LIMITATION OF WARRANTY - UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL, INCIDEN-
TAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT LIABILITY,
OR ANY OTHER LEGAL THEORY. SUCH DAMAGES INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE SOFTWARE PRODUCT
OR ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT, FACILITIES OR SERVICES, DOWN
TIME, PURCHASERS TIME, THE CLAIMS OF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO PROPERTY. WARNING: DSC recommends
that the entire system be completely tested on a regular basis. However, despite frequent testing, and due to, but not limited to, criminal tampering
or electrical disruption, it is possible for this SOFTWARE PRODUCT to fail to perform as expected.
INDUSTRY CANADA STATEMENT
CAN-ICES-3(B)/NMB-3(B)
© 2015 Tyco Security Products. All Rights Reserved.
Tech. Support: 1-800-387-3630 (Canada & U.S.), 905-760-3000
Toronto, Canada • www.dsc.com