Télécharger Imprimer la page
Shindaiwa PowerBroom 99909-34000 Instructions
Shindaiwa PowerBroom 99909-34000 Instructions

Shindaiwa PowerBroom 99909-34000 Instructions

Kit de conversion

Publicité

Les langues disponibles

Les langues disponibles

Liens rapides

C
:
ontents
Gear Case/ Sweeper Assembly
Tube guard
Front handle assembly
IMPORTANT
The terms "left," "left-hand," and "LH": "right," "right-hand," and "RH"; "front" and "rear" refer to directions as
viewed by the operator during normal operation of the unit.
A
:
ssembly
1. Remove existing gear case assembly from unit.
2. Install tube guard (A) onto outer shaft tube.
3. Remove drum assembly from drum axle (C) on right
hand side of gear case.
4. Loosen clamping bolt on gear case (D) and remove
self-tapping screw (E).
NOTE
Assure that locating hole of internal collar aligns with
locating hole in gear case.
5. Slide gear case onto outer tube. Secure gear case by
tightening clamping bolt (D).
into locating hole (E) in gear case.
IMPORTANT
Assure gear case and engine remain properly
aligned while installing self-tapping locating screw.
6. Install drum assembly on to drum axle (C).
IMPORTANT
Drum must be installed with its recessed end facing toward the gear case.
7. Use cotter pin (B) to secure the drum assembly on the axle (see inset). The cotter pin is designed to fit tightly
against the outboard end of the drum, so you may need to compress the drum face slightly during installation.
Spead the ends of the cotter pin to secure.
CAUTION!
After converting your trimmer to a Power Broom, access www.shindaiwa.com or call Shindaiwa at 1-877-986-
7783 to get an appropriate Power Broom operator's manual.
H
:
Andle
1. Remove existing handle from outer tube.
2. Remove adjustment knob (A). Locate the front handle assembly
at the best position for operator comfort (usually about 10 inches
ahead of the throttle trigger). Install and tighten adjustment knob.
X7672231600
04/11
SHINDAIWA INSTRUCTIONS
Power Broom Conversion Kit
99909-34000
1
Cotter Pin
1
Assembly Tool (s)
1
Install self-tapping screw
A
E
D
D
E
B
C
B
Copyright© 2011 By Echo, Incorporated
All Rights Reserved.
1
A
A

Publicité

loading

Sommaire des Matières pour Shindaiwa PowerBroom 99909-34000

  • Page 1 Spead the ends of the cotter pin to secure. CAUTION! After converting your trimmer to a Power Broom, access www.shindaiwa.com or call Shindaiwa at 1-877-986- 7783 to get an appropriate Power Broom operator’s manual. Andle 1.
  • Page 2 Power Broom, acceda a www. shindaiwa.con o llame a Shindaiwa 7. Utilice una chaveta (B) para fijar el conjunto del tambor al eje de al 1-877-986-7783 para obtener un transmisión (consulte la página insertada). La chaveta está diseña-...
  • Page 3 PowerBroom, aller sur orientée versle boîtier d’engrenage. www.shindaiwa.com ou téléphoner à Shindaiwa au 1-877-986-7783 7. Utiliser goupille fendue (B) pour fixer le tambour sur l'axe pour obtenir le manuel d’utilisation (voir illustration). La goupille fendue est conçue pour ap- PowerBrown applicable.
  • Page 4 Avant d’appeler, veiller à disposer des numéros de modèle et de série de l’unité afin d’aider votre représentant du service après-vente. ECHO Incorporated. Yamabiko Corporation 400 Oakwood Road 7-2 Suehirocho 1-Chome, Ohme, Tokyo, 198-8760, Japan Lake Zurich, IL 60047-1564 U.S.A. Phone: 81-428-32-6118 Telephone: 1-877-986-7783 Fax: 81-428-32-6145 Fax: 1-847-540-8416 www.shindaiwa.com...