Operating Instructions; Maintenance And Adjustments - Jiffy 4G Mode D'emploi Et Pièces Détachées

OPERATING INSTRUCTIONS

COLD STARTING PROCEDURE: Starting engine for the first time or
after engine has cooled off or after running out of fuel.
1. ON-OFF switch is automatically in the run position to start
engine.
2. Press primer bulb until gas (return) line is free of bubbles,
NOTE – you cannot over prime.
3. Move choke lever to FULL CHOKE or (I\I) position.
(operator's left)
4. Depress throttle control with left hand and grasp the starter
handle in right hand.
5. Slowly pull starter handle until you feel resistance from
engine, then pull to start with short quick strokes until
unit starts or you get a false start or pop.
6. After a false start or pop, move choke lever to HALF
CHOKE and pull to start with short, quick strokes.
7. If engine fails to start after 2-3 pulls, repeat steps until unit
starts.
8. Once unit starts, let engine warm and then move choke to
off position (operator's right).
9. To stop engine, push rocker switch to OFF or (O) position.
Please view starting video on Jiffy website
www.jiffyonice.com
USING YOUR JIFFY 4G ICE DRILL
NOTE: To minimize water splash, back-off throttle when the
drill breaks thru ice, then raise drill slowly.
NOTE: The clutch slips when the drill is overloaded, when
this happens, raise complete unit slightly to ease load.
NOTE: Remove blade protector from drill assembly prior to
drilling. Reinstall when drilling is complete.
NOTE: If drilling additional holes, turn the engine off and
carry unit in upright position by handles only, to next
location and proceed with normal starting and
operating instructions.
1. When all holes have been drilled, and engine is stopped, lay
unit down, resting on wing handle with engine spark-plug facing
upward. Disconnect drill assembly from powerhead by sliding
E-Z Connect™ Collar down and pulling clevis pin from drill
assembly. Do not remove pin from collar tether. Slip drill
assembly off of engine output shaft, then re-insert clevis into
drill assembly and slide E-Z Connect™ Collar up to cover clevis
pin.
2. Reattach blade protector to drill assembly to prevent damage to
the blade teeth and point.
TRANSPORTING AND STORAGE
1. Disconnect spark plug wire from spark plug and keep it away
from spark plug.
2. Make sure all fuel is drained from fuel tank, and fuel cap is
screwed on tight.
3. Never store powerhead with fuel in tank indoors or in enclosed,
poorly ventilated enclosures where fuel fumes may reach an
open flame, spark or pilot light as on a furnace, water heater,
clothes dryer, etc.
4.
Always transport and store powerhead with powerhead in
an upright (operating) position
facing upward. Make sure powerhead and drill assembly
are properly anchored to prevent damage.
or engine spark-plug
IMPORTANT NOTE: TRANSPORTING YOUR JIFFY ICE DRILL
When transporting your Jiffy Ice Drill on an ATV or snowmobile,
it is extremely important to follow these instructions and use
caution to avoid damage to the power head (engine and
transmission) or related equipment:
There are many after-market ice drill carrier mounting systems
to choose from. Make sure the carrier system you purchase or
use has the proper support for the power head. Many systems
are designed to only support and mount to the lower drill
assembly. This leaves the power head unsupported.
situation will result in major damage to the engine and
transmission. Take the necessary steps insure proper support
of the power head as noted above. If the power head is not
properly supported during transportation, this will void the
limited warranty and all repairs or replacement costs will be the
responsibility of the owner.
mounting system
transporting the auger.
NOTE: To further protect your power head when transporting,
make sure the power head is covered to minimize any snow or
ice build-up or accumulation on any of the functional engine
parts, such as the carburetor, throttle, or throttle cable
assemblies. Jiffy has an accessory power head cover (Jiffy
#4022) to protect the power head from these types of
conditions and can be purchased at most retail locations.

MAINTENANCE AND ADJUSTMENTS

Check SPARK PLUG, periodically.
1. Before removing plug, wipe dirt and debris from spark plug base.
2. Remove and inspect spark plug for carbon build up.
3. Replace spark plug if electrodes are pitted, burned, or porcelain is
cracked. For replacement use: Jiffy® Spark plug #4290 Autolite®
4194 spark-plug or equivalent. Failure to use proper spark-plug
may result in engine damage.
4. Check spark-plug gap with wire feeler gauge and set gap at
0.018".
5. Install spark plug in engine and tighten securely and reattach
ignition wire to spark plug.
Significant care should be taken regarding operational components on
your Jiffy® Ice Drill due to the extreme cold environment and other elements
that your Jiffy® Ice Drill is subjected to during use and storage. Melting
snow, water and slush are all thing that can cause freeze-up of these
components, which could make them inoperable. Many of these items are
the result of transporting your Jiffy® Ice Drill on a sled or other device pulled
behind an ATV or snowmobile, where water, slush, and snow can be thrown
up, collect and freeze on these components. During off season storage, your
Jiffy® Ice Drill is also subject to dirt and debris which could cause operational
concerns. Some type of power head cover should be used when subjected
to these types of conditions.
Cover part #4022, to help protect these conditions.
THROTTLE LEVER AND CONTROL CABLE – This assembly and the
carburetor throttle shaft should be checked before each use for proper
movement and function.
periodically by spraying silicone spray down both ends of the throttle cable
sheath, as well as on the throttle shaft on the carburetor. See below for
lubricating points. This lubricating procedure should also be performed at the
end of the season before storage. Also check throttle cable for any bends or
kinks, which can also cause improper operation of the throttle assembly.
-4-
Purchase the correct carrier
and exercise extreme
Jiffy® recommends the Jiffy® Powerhead
These components should also be lubricated
This
caution when
Lubricate