Roller Worklight 10000 Notice D'utilisation page 19

delivered pre-charged to approx. 40 %. Therefore the Li-Ion batteries must be charged before use and
recharged regularly. Failure to observe this regulation of the cell manufacturer can lead to damage to the
Li-Ion battery by total discharging.
Total discharging due to storage
If a relatively low charged Li-Ion battery is stored, self discharging can lead to total discharge damage of the
battery after longer storage. Li-Ion batteries must therefore be charged before storing and recharged every
six months at the latest and charged again before use.
NOTICE NOTICE
Charge the battery before use. Recharge Li-Ion batteries regularly to avoid their total discharge. The
rechargeable battery will be damaged by total discharge.
Only use a ROLLER'S rapid charger for charging. New Li-Ion batteries and Li-Ion batteries which have not
been used for a long time only reach full capacity after several charges.
Graduated charging state display of the Li-Ion 21.6 V battery
The graduated charging state display (2) shows the charging state of the battery (1) with 4 LEDs. At least one
LED lights for a few seconds after pressing the key with the battery symbol. The more LEDs that light green, LED lights f LED lights for a few seconds after pressing the key with the battery symbol. The more LEDs that light green,
the higher the charging state of the battery. If a LED fl ashes red, the battery must be charged.
Rapid charger Li-ion
The left control light lights up and remains green when the mains plug is plugged in. If a battery is inserted light light lights up and remains green when the mains plug is plugged in. If a battery is inserted
in the ROLLER'S rapid charger, the green control light fl ashes to indicate that the battery is charging. The
green light stops fl ashing and remains on to signal that the battery is fully charged. If the red control light
fl ashes, the battery is defective. If the red control light comes on and remains on, this indicates that the
temperature of the rapid charger and / or the battery is outside the permissible range of 0°C to +40°C.
NOTICE NOTICE
The rapid charger is not suitable for using outdoors.
2.2. Preparing the electric LED fl ood light
Mounting the stand (Fig. 2), ROLLER'S Worklight 10000
Fasten the tubular steel frame (3) with spring ring (4), washer (5) and star screw (6).
3. Operation
NOTICE NOTICE
Keep the LED fl ood light the permissible minimum distance of ≥ 1 m away from all illuminated surfaces
and objects. The illuminated objects can overheat below this distance.
Installation
Place the LED fl ood light on fi rm, level ground. Loosen the wing screws/star screws (8) slightly if necessary
and swing the fl ood light housing (7). Re-tighten the wing screws/star screws (8).
Fastening to the ROLLER'S telescopic stand 3B (Fig. 4)
Adjust the ROLLER'S telescopic stand 3B as shown in Fig. 4 and place it on fi rm, level ground. For ROLLER'S
Worklight 10000, remove the tubular steel frame (3) and fasten the LED fl ood light to the ROLLER'S telescopic
stand 3B with the stand screw (13). Loosen the wing screws/star screws (8) slightly if necessary and swing
the fl ood light housing (7). Re-tighten the wing screws/star screws (8). light housing (7). Re-tighten the wing screws/star screws (8). light
NOTICE NOTICE
Observe the load carrying capacity of the ROLLER'S telescopic stand 3B of ≤ 10 kg.
Hanging up, ROLLER'S Worklight 2800 22 V
Unfold the hook (10) and hang up the LED fl ood light on a suitable object. Loosen the wing screws (8) slightly
if necessary and swing the fl ood light housing (7). Re-tighten the wing screws (8).
Operation
ROLLER'S Worklight 10000 can be set for 2 selectable brightness stages with the on/off switch (11).
Switch the ROLLER'S Worklight 2800 22 V on or off with the button (11) and set one of the 3 selectable
brightness stages with the button (12).
light light the permissible minimum distance of ≥ 1 m away from all illuminated surfaces
light light on fi rm, level ground. Loosen the wing screws/star screws (8) slightly if necessary
light light housing (7). Re-tighten the wing screws/star screws (8).
light light housing (7). Re-tighten the wing screws (8).
light light fl ashes to indicate that the battery is charging. The
light light comes on and remains on, this indicates that the
light light on a suitable object. Loosen the wing screws (8) slightly
light light to the ROLLER'S telescopic
eng
19