Franklin Electric Little Giant L1C Mode D'emploi

Franklin Electric Co., Inc.
oklahoma City, oK 73127
www.lg-outdoor.com
customerservice@lgpc.com
E N G L I S H
ENGLISH
EN
This instruction sheet provides you with the information required
to safely own and operate your product. Retain these instructions
for future reference.
The product you have purchased is of the highest quality
workmanship and material, and has been engineered to give you
long and reliable service. This product has been carefully tested,
inspected, and packaged to ensure safe delivery and operation.
Please examine your item(s) carefully to ensure that no damage
occurred during shipment. If damage has occurred, please
contact the place of purchase. They will assist you in replacement
or repair, if required.
READ THESE INSTRUCTIONS
ATTEMPTING TO INSTALL,
YOUR PRODUCT. KNOW THE PRODUCT'S APPLICATION,
LIMITATIONS, AND POTENTIAL
YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/
OR PROPERTY DAMAGE!
DESCRIPTION
The L1C underwater light is a heavy-duty submersible light for
illuminating fountains, reflecting pools, and ponds. The light
features a stainless-steel case, a cast brass rock guard, and a 250-
watt, high-output tungsten halogen lamp. The low-profile design
of the L1C enables it to be placed in water as shallow as 6 inches.
The L1C includes a swivel base, which allows easy placement of
the light in a pond or fountain.
SAFETY GUIDELINES
To reduce the risk of electrical shock, connect the light to a
properly grounded, grounding-type receptacle. Never remove or
disable the grounding pin of the cord plug.
UNDERWATER LIGHT
LUMIÈRE SOUS-MARINE
LUZ SUBACUÁTICA
Model L1C
CAREFULLY BEFORE
OPERATE, OR SERVICE
HAZARDS. PROTECT
TO COMPLY WITH THESE
The National Electric Code and many local building codes require
the use of a ground fault circuit interrupter (GFCI) on the branch
circuit supplying fountain equipment rated above 15 volts.
WARNING: ThIs LIGhT Is dEsIGNEd FoR submERGEd usE
oNLy. do not use this light out of the water because excessive
heat may result in burns or fire.
Always disconnect the electrical power and remove the light from
the water before attempting any maintenance or lamp replacement.
This light is intended to be placed in fountains, waterfalls, and ponds.
The light has not been approved for swimming pool or spa use.
To avoid shock or injury do not use this light with extension cords.
Always disconnect power to the light when installing, relocating,
or handling the light.
Adhere to the guidelines of the National Electric Code (NEC) or
Canadian Electric Code (CEC) and any other national, state, and
local electric, plumbing, and building codes for ALL installations.
Check with the appropriate agencies or a water systems
professional for information. The installation of this product must
be in accordance with applicable regulations.
ASSEMBLY
Refer to Figure 1 and the following steps to assemble the light:
1. Attach the stainless steel brackets (2) to the base (4) using
the included bolts (3). Install the brackets so that they slope
outward from the base, and with the rounded edge of the
bracket facing upward.
2. Attach the light to the brackets (2) with the included bolts (1)
using the holes threaded into the rock guard (5).
3. Tilt the light to the desired angle and then tighten the upper
bolts. CAuTIoN: Tightening the bolts excessively will damage
the base and void the warranty.
INSTALLATION AND OPERATION
1. Place the light in the desired location where it will be
completely submerged.
2. Connect the light to a properly grounded 115-volt power source
that is protected by a ground fault circuit interrupter (GFCI).
3. In some advanced installations it may be necessary to splice
power cables underwater. In these installations you must use
an approved underwater junction box. use only a junction box
approved for the application. Read and follow all instructions
provided with the junction box.
MAINTENANCE
LAmP REPLACEmENT:
1. disconnect power to the light and remove the light from the water.
2. Remove the four bolts securing the rock guard to the case. use
penetrating oil on the bolts if they are difficult to remove. Remove
the rock guard and lens.
3. double-check to ensure that the power to the light is off, then
remove the old lamp from the socket. Inspect the lamp socket and
remove any rust or corrosion.
1