Publicité
Les langues disponibles
Les langues disponibles
Determine where you want to mount the gate. For optimum safety,
the mounting location must be a solid wood or metal surface.
Do not mount the gate less than 2" (5 cm) or more than 3" (7.6 cm)
above the floor.
1. Using adhesive tape, attach the mounting template on the solid
wood surface that you have chosen for the hinged side of the gate.
Make sure the mounting template is in a straight vertical position
(Fig. 1).
2. Drill four 1/8" (3 mm) diameter pilot holes approximately 3/4" (2 cm)
deep into the mounting surface at the marks on the template.
3. Remove the template from the wall.
4. Using the #10 x 3/4" (2 cm) hinge screws provided, attach the two
Hinge Brackets to the mounting surface as shown in Fig. 2.
5. Attach the gate to the Hinge Brackets by sliding the hinge side of
the gate down through the Hinge Brackets until the gate is securely
seated (Fig. 3).
6. On the opposite side of the opening, make a mark for mounting
the bottom screw eye 6" (15.2 cm) up from the top of the flooring
or carpet (Fig. 4).
7. Measure up exactly 23-3/8" (59.5 cm) from the bottom mark
and make a mark for the top screw eye (Fig. 4).
8. D
rill two pilot holes, approximately 3/4" (2 cm) deep, for the screw
eyes using an electric drill with a 1/8" (3 mm) bit. Screw one of the
screw eyes into each hole until no thread is visible.
9. Attach the gate by inserting the hook into lower screw eye (Fig. 5)
and secure the locking latch to the top screw eye (Fig. 6).
Your Stairway Swing Gate is a hinge mounted gate that, when
installed correctly, should not swing out over a stairway or into a
heavy traffic area. Before proceeding with your installation, refer to
Fig. 7 to determine which way you want your gate to swing.
10. Position the solid surface of the swing stop toward the hazard
(the direction you want to prevent the gate from swinging into).
Using the #10 x 1/2" (1.2 cm) screws provided, attach the swing stop
to the top rail of the gate (Fig. 7).
Operating Instructions:
To open gate, unlock the locking latch, raise gate to clear the hook
and swing out of the way. The gate may be quickly and easily
removed from the opening by unlocking the latch and lifting the
gate out of the hinge brackets.
Installation Instructions
FIG. 1
EZ IC I
PE RC
UN E
AV EC
DR IL L
E DE
HE RE
MÈ CH
1/8 PO
.
W IT H
T
1/ 8" BI
PL AC E
OF
ED GE
LA TE
TE MP
OO R
ON FL
LE
PL AC EZ
DU
BO RD
RIT SU
R
GA BA
AN CH
ER
LE PL
LA
PL AN TIL
FIJ A LA
A LA
NT AJ E
DE MO
ICI E
SU PE RF
FIR ME
ti n g
M o u n
r
la te fo
T e m p
a y
S ta ir w
G a te
S w in g
l 4 6 3 0
M o d e
t d e
G a b a ri
r
rt p o u
s u p p o
re
b a rr iè
n te
o s c il la
li e r
d 'e s c a
0
le 4 6 3
m o d è
EZ IC I
PE RC
UN E
AV EC
DR IL L
E DE
MÈ CH
.
HE RE
1/8 PO
W IT H
T
1/ 8" BI
PL AC E
OF
ED GE
LA TE
TE MP
OO R
ON FL
LE
PL AC EZ
DU
BO RD
R
RIT SU
GA BA
ER
AN CH
LE PL
FIG. 2
2
3
"
3
/
8
(59.5
cm)
6 "
(15.2
cm)
FIG. 4
FIG. 3
Publicité
