Publicité
Les langues disponibles
Les langues disponibles
INSTALLATION
1. Select a location to mount the Keyless Entry at a
minimum height of 5 feet (1.5 m) out of the reach of
children.
2. Remove battery cover and battery.
3. Mark the top mounting hole and drill 1/8 inch (3.2 mm)
pilot hole.
4. Install the top screw, allowing 1/8 inch (3.2 mm) to
protrude above the surface. Position the Keyless Entry
over the top screw.
5. Mark the bottom hole and drill 1/8 inch (3.2 mm) pilot
hole. Install the bottom screw. Do not overtighten to
avoid cracking the plastic housing.
6. Reinstall battery and replace cover.
For additional programming instructions or additional help please visit
http://www.chamberlain.com/CatalogResourcesV3/en-us/shared/files/tucmanuals/114A5071.pdf
OPERATION
The garage door opener activates when the PIN and ENTER
button are pressed. The keypad will blink for 15 seconds, during
that time the ENTER button can be used to stop, start or reverse
the door.
If the wrong number is accidentally pressed, press the correct
PIN then the ENTER button. The Keyless Entry will transmit only
the last four digits that were pressed before the ENTER button.
ONE BUTTON CLOSE: The Keyless Entry has a feature that allows
the door to be closed using the ENTER button instead of a PIN.
NOTE: This feature is not available on garage door openers
manufactured prior to 2006 or an external receiver.
To deactivate the one button close
feature:
Press and hold the 1 and 9 buttons for
10 seconds. The keypad will blink four
times when the one button close
feature is deactivated.
To activate the one button close
feature:
Press and hold the 1 and 9 buttons for
10 seconds. The keypad will blink
twice when the one button close
feature is activated.
BATTERY
WARNING
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
CAUTION
• If battery is swallowed, immediately notify doctor.
Replace the battery when the
keypad becomes dim or does
not light after a button is
pressed.
Dispose of old battery
properly.
AVERTISSEMENT
ATTENTION
NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or
modifications of this receiver and/or transmitter are prohibited, except for changing
the code setting or replacing the battery. THERE ARE NO OTHER USER
SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Wireless Keypad 940EV: IFT #: RCPCH9418-0361
Wireless Keypad 940EVC: IFT #: RCPCH9418-0361-A1
REPLACEMENT PARTS
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10A25
Keypad Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D621
Battery Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41D541
WARRANTY
ONE YEAR LIMITED WARRANTY
The Chamberlain Group, Inc. warrants to the first consumer
purchaser of this product that it is free from defect in materials
and/or workmanship for a period of 1 year from the date of
purchase.
www.chamberlain.com/CatalogResourcesV3/en-us/shared/files/tucmanuals/114A5044SP.pdf
9V Battery
Para Manual en Español ir a:
Publicité
