Publicité
Les langues disponibles
Les langues disponibles
equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC type approval ID: 2ABVH-INARI8C1
RF Exposure Information (SAR)
This model device meets the government's requirements for exposure to radio waves. This device is designed and
manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U. S. Government. The exposure standard for wireless devices employs a unit of
measurement known as the Specific Absorption Rate, or SAR. The regulatory SAR limit set by the FCC is 1.6 W/kg, the
maximum measured single transmission SAR is 1.091 W/kg. Tests for SAR are conducted using standard operating
positions accepted by the FCC with the device transmitting at its highest certified level, the actual SAR level of the device
while operating can be well below the maximum value. This is because the device is designed to operate at multiple
power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base
station antenna, the lower the power output.
While there may be differences between the SAR levels of various devices and at various positions, the all meet the
government requirement.
The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be
found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on the below:
FCC ID: 2ABVH-INARI8C1
This device is compliant with SAR for general population / uncontrolled exposure limits in SNAI / IEEE C95.1-1999 and had
been tested in accordance with the measurement methods and procedures specified in the Office of Engineering and
Technology (OET) Laboratory Division Knowledge Database (KDB), 447498 D03.
Specific Absorption Rate (SAR): 1.091 W/kg
This product has been tested and found to comply with the following standards:
•
For the worst case positions, the INARI8 is in compliance with the IC RSS 102 Issue 5 (RSS 102) and Federal
Communications Commission (FCC) Guidelines (KDB) 447498 D03 for uncontrolled exposure.
SAR assessment in body worn was conducted with a distance of 0 mm between the housing of the handheld
and the flat phantom.
•
EM 62311:2008: Assessment of electronic and electrical equipment related to human exposure restrictions
for electromagnetic fields (0 Hz – 300 GHz).
Radio Frequency Interference Requirements - Canada
CAN ICES-3 (B)/NMB-3(B)
Radio Transmitters
This device complies with Industry Canada's licence-exempt RSSs. Operation is subject to the following two conditions: (1)
This device may not cause interference; and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radio électrique subi même si le brouillage est susceptible d'en
compromettre le fonctionnement.
For RLAN Devices:
INARI 8 (INARI8C) – Quick-Start-Guide – EN
7
Publicité
