R.U. Ready Speed-Timer 3000 Mode D'emploi

Speed-Timer 3000 and 3000 (RF) Operating Instructions.
Speed-Timer 3000 and 3000 (RF): Install a 9 volt Alkaline Battery in the battery compartment of the Speed-Timer 3000
and 3000 (RF)
Shot Time: Practice Mode (2.5 to 5.0 second Random Delay Start Signal) Press and hold down the CTRL key from one
to three seconds ("dEL" will appear on the screen) then release the CTRL key to initiate the Record Mode with 2.5 to 5.0
second Random delay start. Wait for the audible start signal and begin shooting. Then read the number of shots fired, the
elapsed time, and the split time between the last two shots fired.
Range Officer Mode: (instant start signal)
Press and hold down the CTRL key for three seconds ("0 sec" will appear on the screen) then release the CTRL key to
initiate the Record Mode for an instant start. Then read the number of shots fired, the elapsed time, and the split time
between the last two shots fired.
Review Mode:
To review all shots fired (in order), press and release (less than one second) the CTRL key and start cycling through the
shots fired. Press and release (less than one second) for all remaining shots.
On/Off
The display will automatically shut off when not in use for more than one minute during the Review Mode or while in the
review you may press the PAR key to shut the timer off. You will not lose the shot times in memory. Press and release
the CTRL key at any time for less than one second to reactivate. Speed-Timer 3000 and 3000 (RF) will turn itself off after
10 minutes of none use.
PAR Time: Setting PAR Time
While in Shot Time, the PAR time keys are deactivated preventing any accidental interruption in recording shots fired. The
PAR time screen can only be activated by pressing and releasing the PAR key from the Review Mode or if the timer is off.
Press and release the PAR key. The screen will display OFF. Using the up arrow key move the clock to the desired time.
(holding down a arrow key will cause the time to cycle at a faster rate) Press the CTRL key to exit PAR setting. The PAR
time is set and may be operated in either random delay start or instant start with full review capabilities. Note: The letter P
will be present to indicate PAR time is active and set.
True PAR Time
The timer will now sound two audible signals. The first signal to start, and a second at the expiry of the set time. From the
very start of the first signal to the very end of the second signal, will be exactly the time selected. Any and all shots after
the end of the set time will flash indicating true overtime shots. Only shots after the signal (flashing) are true overtime
shots.
To exit PAR time and return to Shot Time.
From the Review Mode, press and release the PAR key to exit and press and release again. Arrow down until the screen
reads OFF. Press the CTRL key to exit.
Sensitivity Adjustment
The Speed-Timer 3000 is factory set for a sensitivity to handle the majority of Firearms indoors and out. It is set to pickup
shots from approximately 20 Feet (6 Meters) from the Timer. Under normal circumstances there is no need to change
these setting, however this Timer can be modified to suit a particular location or application if necessary.
Should you find that this setting requires adjustment you can proceed as follows:
Turn the Speed-Timer 3000 face down with the Belt Clip facing you. Through the hole on the left side back of the Speed-
Timer 3000 you will notice a white Philips head adjusting screw. Turning this adjusting screw in very small increments
Counter Clockwise (Left) will decrease the sensitivity, turning the adjusting screw Clockwise (right) in very small
increments will increase the sensitivity. This adjustment should be tested for satisfactory results between each adjustment
of the screw.
Please note that this adjustment screw does not turn more than 270 Degree's and care should be taken not to try to turn
this screw past its stop positions. Failure to follow this instruction can damage the Timer.
Hint:
Use a small screwdriver so you can feel the rotation for the adjustiment
and do not force. Factory setting for this adjustment is approximately half way between the fully clockwise and
anti clockwise stops.
To Use the Hands Free Carry Case (Sold Separately)
Can protect your Speed-Timer 3000 when not in use.
Will attach to your Belt for secure and easy access while recording shots. Just fold the flap back, attach the flap to the