Martinelli Carrello Book 51 s Mode D'emploi page 11

INSTRUCTIONS
1 OPENING: Before opening the frame, remove (without
using blades) any die-cut cardboard.
WARNING:
_ DO NOT PULL OR FORCE THE FASTENER BEYOND
ITS LIMIT.
_ DO NOT USE THE FASTENER AS A CARRY HANDLE
OR TO CARRY WEIGHTS.
DO NOT HANG BAGS OR OTHER ACCESSORIES TO
THIS FEATURE.
Press down the side fastener, hold the upper section
of the handle and rotate it towards you until the
frame is fully opened (fig_a). Open frame (fig_b).
The frame is properly opened when the attachment on
the base clicks into place, as shown. CAUTION: When
placing the seat on the frame, press the seat downwards
to ensure it engages securely onto the base.
2 FITTING THE WHEELS: Slot the uprights into the rear
wheel crosspiece (fig_a), ensuring that it is facing the
right way, then push the rear wheels on and make
sure that they click into place (fig_b). To mount the
front wheels, fit them into the uprights until they lock
into place (fig_c).
THE HANDLE BAR
Assembly and characteristics are different
according to handlebar purchased (OPTION A or
OPTION B)
3 FITTING THE HANDLE BAR OPTION A
insert the handlebar into the frame (fig_a) as shown
in the picture. For the attachment to be complete,
press the two buttons on the side of the handle bar
(fig_b) and press the handle bar until you hear it click
(fig_c).
4 FITTING THE HANDLE BAR OPTION B
Fasten the handle to the frame as shown in the figure
(Fig_a). To complete the operation, press the two side
buttons on the handle (Fig_b) to ensure the handle
pushes in all the way, until it clicks into place (Fig_c).
5 FITTING THE BASKET: if lowered, lift the basket tube
to the horizontal position. Press the silver buttons
under the metal basket tube located at the back of
the stroller (fig_a) and remove the metal tube (fig_b).
Thread the tube through the fabric loop on the back
of the basket, making sure that the two silver buttons
are facing downward (fig_c). Re-attach the tube to the
housings (fig_d).
6 Secure the two upper basket vinyl eyelets to the two
grey buttons on either side of the metal tube housing.
Please note that the eyelets open (fig_e). Remove the
cardboard from the lower rear bar.
IMPORTANT! Secure the two lower basket vinyl
eyelets to the two grey buttons on the top of the
lower rear bar. Please note that the eyelets open
(fig_f).
WARNING! If this operation is not performed
correctly, the basket will not properly hold the
weight.
Attach the basket tabs to the grey buttons on the
front of the frame (figure).
7 FIXED OR SWIVEL FRONT WHEELS Book 51 S: to fix the
front wheels, rotate the lever counter clockwise to the
locked padlock (fig_a); to release the wheels, turn the
lever clockwise to the unlocked padlock (fig_b). On
difficult terrain, we recommend using fixed wheels.
8 BRAKE: Press the lever down to apply the brake on the
chassis and lift it to release the brake.
9 ADJUSTABLE HANDLE BAR OPTION A
to adjust the height of the handlebar, pull the levers
towards you (fig_a) and move the handle bar until
it clicks (fig_b). The handle bar can be adjusted in
several positions.
10 FOLDING UP OPTION A
The chassis can be folded up without the seat, with
the seat facing the person pushing (recline the
backrest before folding it) or with the seat facing
forward. To fold the stroller, it is best to set the front
wheels to their fixed position and close the hood
(if fitted). Put the handle bar to its lowest position
(fig_a). Pull the inside handle on the base (fig_b) and
lift it (fig_c); the handle will drop forward until the
frame is closed.
11 TELESCOPIC HANDLEBAR OPTION B
to lengthen the handlebar, pull the sde buttons
upwards (fig_ a) and legthen (fig_b).
12 FOLDING UP OPTION B
The chassis can be folded up without the seat, with
the seat facing the person pushing (recline the
backrest before folding it) or with the seat facing
forward. To fold the stroller, it is best to set the front
wheels to their fixed position and close the hood (if
fitted). Place the handle as shown in the figure (fig_a).
Pull the inside handle on the base (fig_b) and lift it (fig_c);
the handle will drop forward until the frame is closed.
13 To ensure the frame is closed properly, check that
the side fastener is enabled (fig_a). When closed, the
frame remains in the upright position (fig_b).
14 For greater compactness, it is possible to remove the
wheels.
To remove the rear wheels: pull outwards on the lever
located under the rear bar and remove the wheels as
shown in figure (fig_a).
To remove the front wheels: press the tab as shown,
and remove the wheel (fig_b).
TRANSPORT: the stroller can be carried comfortably
locking the front wheels and grasping the main handle
(fig_c).
GANCIOMATIC SYSTEM
15 Ganciomatic is a fast and practical system that allows
you to attach the Navetta bassinet unit, the Primo
Viaggio car seat or the Seggiolino Pop Up seat to the
Ganciomatic Base of the chassis in one quick step.
Place the item on the Ganciomatic Base and press
down with both hands until it clicks into place.
Always apply the chassis or stroller brake before
attaching and removing products (refer to the
respective instruction manuals).
Check that the child transport unit is properly attached.
SERIAL NUMBERS
16 Information about the production date can be found
on the Carrello Book 51 S.
_ The product name, production date and serial number
of the chassis.
This information is required for any complaints.
CLEANING AND MAINTENANCE
PRODUCT MAINTENANCE: protect from the weather:
water, rain, or snow; prolonged and continuous
exposure to bright sunlight may give rise to colour
changes of various different materials; store this
product in a dry place.
CLEANING THE CHASSIS: periodically clean all plastic
parts with a damp cloth. Do not use solvent or
similar cleaning products; keep all metal parts dry to
prevent rusting; keep moving parts clean (adjustment
mechanisms, locking mechanisms, wheels, ...) and free
of dust and sand and, if necessary, lubricate with light
machine oil.
THE ORIGINAL ACCESSORY PEGPEREGO
Martinelli accessories are designed as a useful, practical
means of simplifying the lives of parents. Discover all
your product's accessories on
www.martinellimilano.com.
MARTINELLI IS A PEGPEREGO
TRADEMARK
PegPerego SpA adopts a quality management system
certified by TÜV Italia Srl in accordance with the ISO
- 11 -