Accessories - Milwaukee 2447-20 Manuel De L'utilisateur

OPERATION
To reduce the risk of injury, always
WARNING
wear safety goggles or glasses
with side shields. The operator and other people
in the work area must wear eye protection in ac-
cordance with ANSI Z87.1. Eye protection does not
fit all operators in the same way. Make sure the eye
protection chosen has side shields or provides
protection from flying debris both from the front
and sides. The employer is responsible for enforc-
ing the use of eye protection by the operator and
other people in the work area. When required, wear
head protection in accordance with ANSI Z89.1.
To reduce the risk of injury to yourself and others,
test the tool before beginning work each day ac-
cording to the "Required Daily Testing" section.
Remove battery pack and fasteners before leaving
the work area, moving the tool to another location,
or handing the tool to another person. Failure to do
so could result in serious injury.
Do not use this tool for fastening electrical
cables. It is not designed for electric cable
installation and may damage the insulation of
electric cables thereby causing electric shock
or fire hazards.
NEVER wedge or hold back the workpiece contact
mechanism during operation of the tool. Never
attempt to clear a jammed workpiece contact by
grasping the discharge area of the tool. Doing so
could result in serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too firmly against the
work. Keep face and body away from the tool. Dur-
ing normal use, the tool will recoil immediately after
driving a fastener. This is a normal function of the
tool. Grip the handle firmly, let the tool do the work,
and do not place a second hand on top of the tool.
Actuation Operation
1. Insert battery pack.
2. Set the power adjustment. Rotate towards + for
heavy-duty applications, rotate towards - for lighter
applications.
3. For sequential actuation:
Line up the fastener to the workpiece. Press the
workpiece contact bracket to the workpiece and
squeeze the trigger firmly. Release trigger.
For contact actuation:
Line up the fastener to the workpiece. Press the
workpiece contact bracket to the workpiece and
squeeze the trigger firmly. Hold the trigger while
removing and reengaging stapler to the workpiece
for continuous stapling.
Reload Indicator
To indicate that the magazine is almost empty of fas-
teners (about 4-5 left), the workpiece contact will not
compress, preventing operation under usual pressure.
Install more fasteners to continue working.
NEVER wedge or hold back the
WARNING
workpiece contact mechanism dur-
ing operation of the tool. Never attempt to clear a
jammed workpiece contact by grasping the dis-
charge area of the tool. Doing so could result in
serious injury.
To avoid serious injury, do not attempt to prevent
the recoil by holding the tool too firmly against the
work. Keep face and body away from the tool. Dur-
ing normal use, the tool will recoil immediately after
driving a fastener. This is a normal function of the
tool. Grip the handle firmly, let the tool do the work,
and do not place a second hand on top of the tool.
Setting the Power Adjustment
The power of the drive can be adjusted to account for
the size of the fastener and the workpiece material.
Know what is behind your workpiece.
WARNING
A fastener could travel through the
workpiece and out the other side, striking a
bystander and causing serious injury. Lower the
power adjustment to prevent the fastener from
being pushed all the way through the workpiece.
1. Drive a test fastener.
2. Remove battery pack.
3. WARNING! Always point the tool away from yourself
and others when making adjustments. Failure to do
so could result in injury.
4. Turn the power adjustment up or down to increase
or decrease the power.
5. Repeat until desired power is reached.
Clearing a Jammed Fastener
Most jams are caused by a fastener or part of a fastener
wedging between the driver blade and the stapler guide.
Fastener strips with a wrong fastener gauge may cause
continuous jamming. To clear the jam:
1. Remove battery pack.
2. WARNING! Always point the tool away from yourself
and others when installing or removing fasteners.
Failure to do so could result in injury.
3. Remove fastener strip from magazine.
4. Pull down on the magazine latch and pull magazine
away from the tool.
5. Remove the fastener and other debris (use needle-
nose pliers if necessary).
6. Close jam latch.
7. Follow the steps under "Required Daily Testing"
before restarting the work.
6
REQUIRED DAILY TESTING
To reduce the risk of injury to your-
WARNING
self and others, test the tool before
beginning work each day or if the tool is dropped,
received a sharp blow, been run over, etc. Complete
the following checklist IN ORDER. If the tool does
not work as it should, contact a MILWAUKEE service
facility immediately.
Always point tool away from yourself and others.
1. Remove battery pack.
2. WARNING! Always point the tool away from
yourself and others when installing fasteners.
Failure to do so could result in injury.
3. Check all screws, bolts, nuts, and pins on the tool.
Any loose fasteners must be tightened.
4. Pinch the magazine latch and pull magazine out
from tool. Press the workpiece contact against a
workpiece. It must move smoothly.
5. With the workpiece contact pressed against the
workpiece, pull the trigger. It must move smoothly.
6. Insert battery pack.
7. Make sure the magazine is still pulled out. Holding
the workpiece contact away from the workpiece,
pull and hold trigger for 5 seconds. The tool must
not operate. Release the trigger.
9. If all previous tests work properly, set the tool for your
work. Select the operation and load fastener strips.
10. Set the power adjustment according to the "Setting
the Power Adjustment" section.
11. If all tests operate properly, the tool is ready for use.
Repeat these tests before use each day or if the tool
is dropped, received a sharp blow, been run over,
jammed, etc.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest service center.

ACCESSORIES

Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST
(1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination,
is determined by MILWAUKEE to be defective in material or workman-
ship for a period of five (5) years** after the date of purchase unless
otherwise noted. Return of the power tool to a MILWAUKEE factory
Service Center location or MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs
made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of
maintenance, or accidents.
Normal Wear: Many power tools need periodic parts replacement and
service to achieve best performance. This warranty does not cover
repair when normal use has exhausted the life of a part including,
but not limited to, chucks, brushes, cords, saw shoes, blade clamps,
o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and
bumper cover washers.
*This warranty does not cover Air Nailers & Staplers; Airless Paint
Sprayer; Cordless Battery Packs; Gasoline Driven Portable Power
Generators; Hand Tools; Hoist – Electric, Lever & Hand Chain; M12™
Heated Gear; Reconditioned Product; and Test & Measurement
Products. There are separate and distinct warranties available for
these products.
**The warranty period for Job Site Radios, M12™ Power Port, M18™
Power Source, Jobsite Fan and Trade Titan™ Industrial Work Carts
is one (1) year from the date of purchase. The warranty period for
the Drain Cleaning Cables is two (2) years from the date of purchase.
The warranty period for the LED in the LED Work Light and the LED
Upgrade Bulb for the Work Light is the lifetime of the product subject
to the limitations above. If during normal use the LED or LED Bulb
fails, the part will be replaced free of charge.
7