Renkforce 1408619 Mode D'emploi page 4

Installation and Connection
Please consult the chapter "Sicherheitshinweise" of these and operating in-
structions of the devices to be connected to the product!
• The product must be protected on the distribution board by a 10/16 A fuse. An earth fault
circuit interrupter must be installed before this (Ground Fault Circuit Interrupter).
• The installation of the product may only take place in a voltage-free condition. It is not suf-
ficient to just turn off the light switch!
Switch off all the poles of the mains cable by removing the corresponding fuse or switching
off at the circuit breaker. Switch off the appropriate earth-leakage circuit breaker afterwards.
Secure it against unauthorised reconnection, e.g., with a warning sign.
• Check that the mains connection is free of current, i.e. with an appropriate tester.
• During the installation, maintain a sufficient distance to other LED drivers or lights.
a) Connection
Caution!
The LED driver may not be connected to a dimmer on the mains side! It may be
connected to mains voltage either directly or via a conventional switch only.
The LED panel must always be connected to the LED driver before the LED
driver is connected to the mains voltage. Otherwise the LED panel can be
destroyed!
• Unscrew the two screws on the right wider cover with a Philips screwdriver and remove it
from the driver housing.
• Connect the suitable LED lighting to the screw terminals on the secondary side (8 connection
terminals on the right) observing correct polarity.
„CH1+" / „CH1-" and „CH2+" / „CH2-"
„CH1" (warm white) is the first and „CH2" (cool white) - the second channel of the driver.
Connect both channels of an LED panel here with the correct polarity. Also observe the con-
nection values in the „Technischen Daten" section of these operating instructions.
Only a suitable LED panel can be connected to the LED driver, which supports
warm/cool white control. With that, the control occurs via a suitable gateway. De-
pending on control settings, either channel 1 or channel 2 alone are driven at full
capacity, or the channels are mixed. Irrespective of the control settings, both chan-
nels are driven with max. 900 mA, in total.
„0-10V in"
You can connect a dimmer at the input „0-10V in" as required. Its regulation range must be 0
to 10 V/DC. Connect the ground connection of the dimmer to the terminal „GND" at the LED
driver.
„Sensor V+ (5V)" and „Sensor In (5V)"
A motion switch can be connected to these terminals. With that, the terminal „Sensor V+ (5V)"
provides the operating voltage of 5 V/DCfor the motion switch. The terminal „Sensor In (5V)"
is the sensor input at the LED driver. Connect the switch contact of the motion sensor to this
terminal. Connect the ground connection of the motion sensor to the terminal „GND" at the
LED driver.
• Once all cables are connected, replace the cover onto the driver housing and fasten it with
the screws.
• Connect the power cable to the mains using e.g., the terminals of the junction box.
The protective earth conductor must be also connected.
• Last of all, make sure that the LED drivers are correctly connected; the mains voltage may
only be restored after flawless installation.
• The LED driver will function as soon as the primary side is energized.
b) Assembly
• Install the LED driver on a level, stable surface (e.g., wall, ceiling). Use suitable screws and/
or dowels matching the surface structure (e.g., concrete, wood...). There are two fixing holes
for this at the side of the LED driver. Alternatively, the driver can be fastened directly onto the
back of an LED panel using e.g., double-sided tape.
• When fastening the product make sure not to damage any power lines or gas or water pipes
distributed below the surface.
Care and Cleaning
• Before cleaning, turn off the mains voltage. Allow the product to cool down completely.
• Use a dry, lint-free cloth to clean the product.
Do not use abrasive cleaning agents, rubbing alcohol or other chemical solutions,
which may damage the casing or even impair operation.
Disposal
Electronic devices are recyclable material and do not belong in the household
waste.
Once the product becomes unusable, dispose of it in accordance with the relevant
statutory regulations.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available via the following Internet
address:
www.conrad.com/downloads
Select language by clicking a flag symbol and enter the order number of the product
in the search field; then you will be able to download the EU declaration of conform-
ity in PDF format.
Technical Data
Operating voltage ..................................... 100 - 240 V/AC, 50/60 Hz
Power consumption .................................. max. 0.56 A
Protection class ........................................ I
Output ....................................................... constant current 900 mA, for both channels
Nominal voltage ........................................ 30 - 54 V/DC
Power consumption .................................. approx. 60 W (without wireless module)
Power consumption, standby ................... 0.5 W
Installation site .......................................... only in dry enclosed rooms
Dimmable ................................................. yes, via separate input, 0 - 10 V/DC
Connection for motion sensors ................. yes
Short circuit protection .............................. yes
Overcurrent protection .............................. yes
Overtemperature protection ...................... yes
Transmission standard ............................. ZigBee
Transmission power.................................. 4 mW
Range ....................................................... max. 30 m
Dimensions (L x W x H) ............................ approx. 186 x 65 x 36 mm
Weight ...................................................... approx. 300 g
Operating and storage conditions ............. Temperature -20 °C to +60 °C, air humidity 0% to
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2016 by Conrad Electronic SE.
; 2.4 GHz
®
90% relative, non-condensing
1408619_V1_0716_02_VTP_m_en