Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
Stroboscope flashgun, 12V/DC
Item no. 1852381
Intended use
This product is intended to be used on a localized alarm installation with 12 V alarm output (power rating min.
400 mA). The stroboscope flashgun produces on activation approx. 90 flashlights per minute.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Stroboscope flashgun
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of personal injury,
such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating manual that
absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Also observe the safety and operating instructions of any other devices which are connected
to the product.
• When setting up the product, make sure that the cables are neither kinked nor pinched and
no short-circuit is caused.
• Only direct current voltage of 12V should be used.
• Use the product only in indoor locations or protected outdoor locations. The product should
not be used in the near vicinity of a bath, swimming pool or a shower.
• Never place the product in explosive areas resp. areas with high dust exposure.
• Only use the product in a moderate climate, and avoid a tropical environment.
• Keep the product away from strong magnetic fields occurring near machines, electric motors
or loudspeakers.
• The product may only be operated when the synthetic cover (A) is unscrewed firmly and
completely.
• The product should not be used within the Highway Code area, it should not be built into
vehicles.
• In commercial and industrial facilities the regulations for the prevention of accidents as laid
down by the professional trade association for electrical equipment and devices need to be
observed.
• Electric devices used at schools, training facilities, do-it-yourself and hobby workshops should
not be handled unless supervised by trained, responsible personnel.
• Do not look into the flashlight, risk of eye injuries.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
Operating elements
A
Red synthetic cover
B
Case with electronics
C Mounting legs
D Connection cable for 12V/DC
(red = plus/+, black = minus/-)
Installation and connection
• Mount the stroboscope flashgun onto an appropriate surface by means of the three mounting legs (C).
Make sure when drilling resp. tightening the screws that no power, gas or water pipes are
damaged!
Do not use force while tightening the screws, as the housing might get damaged.
• Use the product only in indoor locations or protected outdoor locations. The product must not be subjected
to mechanical stress. Locate it e.g. under a roof overhang or such.
• Connect both connection cables according to the colour marking to the 12V direct current voltage (red
cable = plus/+, black cable = minus/-).
Use e.g. screw clamps. When the cable should be welded, use a shrinkable tubing for insulation.
Warning!
If the stroboscope flashgun is mounted freely accessible, a specialist should see to it, that the
synthetic cover (A) cannot be opened without tools.
The inside of the stroboscope flashgun contains high-voltage conducting elements, risk of a fatal
electric shock!
Alternatively e.g. the synthetic cover could be glued (glue might lead to discolouring!).
• If the operating voltage (12V/DC) is switched on, the stroboscope flashgun produces approx. 90 flashlights
per minute.
Care and cleaning
• The product does not require maintenance! The built-in flash tube is not replaceable.
• Use a clean, dry and soft cloth for cleaning.
• Dust can be removed very easily using a clean, soft brush and a vacuum cleaner.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ................................. 12 V/DC
Current consumption ............................ 400 mA
Flash frequency .................................... approx. 90 flashlights per minute
Operating temperature ......................... -10 to +50 °C
Operating humidity ............................... max. 90 % RH (non-condensing)
Dimensions (Ø x H) .............................. 105 x 90 mm
Net weight ............................................. approx. 150 g
Gross weight ......................................... approx. 200 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in
part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
A
B
C
D
C
C
*1852381_V2_1118_02_mxs_m_en
Publicité
