Publicité
Les langues disponibles
Les langues disponibles
OPERATING INSTRUCTIONS
PARTS
HEPA filter
INTENDED USE
Thank you for purchasing this Sensede HEPA air purifier. It is designed to filter out pollutants and dust from the air in your
home. This appliance operates on 220-240V, 50Hz (mains electricity). Never try to connect the device to other power sources.
Please always follow the safety instructions in this manual. Keep this instruction manual in a safe place so that it is available
at all times. This product complies with regulatory, national and European requirements. Never try to make technical
modifications to this device. We do not accept liability for accidents or damages resulting from failure to follow these
operating and safety instructions.
WHAT TO EXPECT
This HEPA (high-efficiency particulate air) air purifier effectively captures pollutants from the air passing through its filter.
The filter unit will normally need to be replaced every 3000 hours of operation* (compatible filter: IFC120). This appliance is
also equipped with an integrated ioniser and air quality sensor.
BEFORE YOU START
Please carefully read the safety instructions on the front page of this manual before
getting started.
PLACEMENT AND INSTALLATION
1. Select a level surface that provides sufficient distance (>30 cm) between the appliance and any walls
and other objects.
2. Detach the front panel. Unpack the HEPA filter (IFC120). Securely push the unpacked filter unit in the appropriate slot.
The light-coloured side should face forward.
3. If needed, install a CR2025 battery in the remote control.
4. Plug in the device. The ON/OFF light will blink.
SWITCHING ON THE APPLIANCE
The appliance can be switched on and off with the ON/OFF touch button on the device, or the ON/OFF button on the remote
control. After switching on the appliance, the display and the ON/OFF button will light up.
AIR VOLUME
You can manually regulate the air volume by using the WIND SPEED button. You can select three air volume settings:
1. - Low noise mode, low-intensity filtration
2. - Normal speed, advised for daily use
3. - High-speed filtration, use for short durations only*
* Example of use: directly after smokers have used the space.
LCD Display
Touch buttons
Air inlet
Front
cover
AIR QUALITY SENSOR
The device will automatically start analysing the air quality. After approximately 30 seconds, the air quality will be displayed
in two ways:
- Detected particles per million will be displayed as a number.
- An indicator displaying green (good) / orange (in-between) / red (poor)
By pressing AUTO, you can set the device to automatically adjust
its speed depending on the measured air quality.
SLEEP MODE
When in sleep mode, the device will work at minimal fan speed to reduce noise. Only the sleep mode indicator will stay lit.
AIR IONISER
The integrated air ioniser can be activated by touching the ANION button. The air ioniser helps remove dust particles from the
air. After activating the ANION function, a soft whir may be audible.
TIMER FUNCTION
The timer function allows you to switch on the air purifier for a set number of hours.
The appliance will automatically shut down after the set time has passed. Touch the TIMING button
on the remote control to set the timer. The time will be displayed on the screen.
FILTER MAINTENANCE
Filter replacement
The HEPA filter (IFC120) has a life span of approximately 3000 hours of normal operation. Replace the filter when the
REPLACE FILTER* symbol lights up on the display, or when it shows signs of severe contamination/ discolouration. After
replacing the filter, press FILTER RESET to reset the filter life interval.
Filter lifespan may be shortened by high-pollution operating conditions (fireplace soot, kitchen fumes, cigarette smoke, etc.).
Regular maintenance
- Gently clean the filter surface with a vacuum cleaner every two months. This removes lint/dust build-up on the filter
exterior and prevents it from getting clogged. Be careful not to damage the filter.
Replace the filter if you accidentally damage it (holes/tears).
- Optionally place the back of the filter (black side) in direct sunlight for approximately 3-4 hours every
two months. This will enhance performance.
- The HEPA filter cannot be washed and should not be cleaned with water, detergents, solvents or
other chemicals.
Please visit the Sensede website for information and service parts (www.Sensede.com)
CLEANING
Dust accumulated around the device air openings can be removed with a vacuum cleaner. If necessary, also wipe off the
exterior of the appliance with a microfibre cloth. Do not use aggressive chemicals or abrasives. Always unplug the device
before cleaning.
DISPOSAL OF THE DEVICE
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your
local government for information regarding the collection systems available. If electrical appliances are disposed of
in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging
your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take
back your old appliance for disposal free of charge.
LIMITED 2-YEAR WARRANTY
ABD guarantees your appliance against material and fabrication faults for two years after your initial purchase. Should material
or fabrication faults be found, ABD will repair or replace the device with a similar or better-specified product. Damage to the device
due to any form of negligence, accident, lack of cleaning and maintenance, or other use or abuse that can reasonably be considered
to be in conflict with the directions described in these instructions, does not fall under this warranty. Furthermore, legal provisions
with respect to consumer purchases apply. In the event of a fault, we advise you to return the product together with the original
proof of purchase to the store where you bought it. When the defect in the device is caused by anything other than material or
fabrication faults, you may be charged for examination and repair costs.
TROUBLESHOOTING
The device cannot be switched on
- Make sure the device is plugged in.
- Check if the front cover is installed correctly.
There is almost no airflow
- Check the filter - make sure it is unpacked, installed correctly.
- Clean the air openings and HEPA filter with a vacuum cleaner to remove dust deposits.
- Replace the filter if it appears severely polluted.
I cannot use the UV -function that is indicated on the remote control
- The UV-sterilization function is not supported on this model version (ACD-600FD). Instead, this model uses a HEPA filter to
filter particles from the air.
The device is noisy
- Check the filter - make sure it is unpacked, installed correctly.
- Make sure the device is placed on a stable, level surface.
- An electronic buzz may be audible when the ioniser function is switched on. This is normal.
The device no longer removes odours and smoke from the air, but the filter has not yet been used
for 3000 hours.
- The filter life span can be shorter than 3000 hours under conditions of intensive use, especially if the device is regularly used
in the presence of tobacco smoke. Check the filter condition and replace it if necessary.
ENGLISH
Publicité
