Little Giant led-l Manuel D'instructions page 2

OPeRatiOn MOde taBle
Operation Mode
sequence number
1
2
3
4
5
6
7
8
9
10
11
* Multi Mode produces random colors and flashing
patterns.
** Color Wheel mode is the smooth color changing
pattern from Aqua to Blue to Purple to Red to Orange
to Yellow to Green and back to Aqua and repeat. The
'Standard' mode gradually changes through all the
colors every 30 seconds. The 'Slow' mode takes 6
minutes to cycle through all the colors before repeating
and the 'Slowest' mode takes 2 hours for each pass
through the colors. For the Color Wheel modes there
is a visual indication of which mode you are in. For
the 'Slowest' mode, the blue LEDs will flash 3 times
before starting the initial gradual changing from Aqua.
For the 'Slow' mode, the green LEDs will flash 3 times
before going to Aqua and transitioning through the color
wheel. The LEDs flash only on the initial startup; on
subsequent cycles of the color wheel the LEDs will not
flash. The 'Standard' color wheel mode does not flash
at all but, starts transitioning in color from Aqua through
its cycle.
selecting Operation Mode
Setting programs is determined by how long the power
is removed before restarting. To switch modes, simply
turn the power switch off for ½ to 3 seconds, and then
back on to advance to the next state.
If the on/off switch is left in the "off" position for 4 to
8 seconds, the LED lights will resynchronize when
powered up by flashing red three times at which point all
of the lights in the system will initialize in the same state
(Mode 1; Red).
If multiple lights are installed, the modes will synchronize
together after synch reset describe above.
2
Color/function
Red
Yellow
Green
Aqua
Blue
Purple
White
Multi Mode *
Color Wheel -
Standard **
Color Wheel - Slow **
Color Wheel - Slowest **
The LED lights have a memory that when switched off for
more than 8 seconds, all the lights will power up in the
last state they were in when powered down. This allows
users to leave lights in a favorite mode without having to
hunt for it when powering up the light. If the unit is turned
off during the running of modes 10 or 11, and the power
is off longer than 8 seconds (color/mode memory state)
the Mode Indicator Flash will reactivate immediately
upon power up. This a visual reminder to you of which
mode is running.
seRViCe instRuCtiOns
MAKE CERTAIN THAT THE UNIT IS DISCONNECTED
FROM THE POWER SOURCE BEFORE ATTEMPTING
TO SERVICE OR REMOVE ANY COMPONENT!
1. Do not remove cord strain relief (hex nut). This will
damage seal and result in possible leakage.
2. BULB REPLACEMENT: NOTE: No tools are required
to service light.
a. Unscrew the outer ring by turning it counterclockwise.
Next, remove the lens and o-ring.
b. CAUTION: The bulb and plastic bulb holder are
one piece. DO NOT pull on the bulb itself. Pull only
on the plastic bulb holder.
c. To install bulb, simply plug bulb into socket as
shown in illustration.
of the bulb are well seated in the two small inner
holes of the socket. DO NOT touch new bulb.
Only touch the plastic bulb holder. Touching the
bulb may shorten bulb life. As you push the bulb
assembly down into the light housing, twist the
bulb assembly so that the openings in the plastic
bulb holder are oriented with the ribs on the inside
of the light housing.
d. Make sure o-ring is in good shape and clean.
Reinstall o-ring and lens.
e. Reinstall the outer ring. DO NOT use any tools.
Tighten outer ring until tab on light ring touches
mounting rib on lamp housing.
CautiOn: MAKE CERTAIN NO WATER OR MOISTURE
IS INSIDE LAMP PRIOR TO THE REASSEMBLING.
3. CLEANING: The lens will require periodic cleaning.
Simply wipe off outside of lens with soft cloth.
DO NOT use abrasives. This may damage lens.
CAUTION: if lamp is disassembled for cleaning, be
certain lamp housing is not submerged in water. This
will allow water to enter cord which could result in an
electrical hazard.
Ensure that the two pins