Publicité
Les langues disponibles
Les langues disponibles
e. If you are not going to need the MKS400 right away you may
leave the MKS400'S internal charger connected to the AC
power source. We recommend that the MKS400's internal
charger remain connected to an AC power source whenever
the MKS400 is not in use.
2. USING THE DC POWER EXTENSION CORD. Plug one end of
the DC power extension cord into the MKS400's power receptacle
and the other end into a vehicle's lighter outlet (the vehicle's
engine should be running first). Push the test button once every
hour to check the unit status by pushing the "Status Button" DO
NOT OVERCHARGE! This is not an automatic method of
charging the MKS400. You must frequently monitor the charging
process to ensure the MKS400 is not overcharged. Overcharging
will damage your MKS400.
Note: Status button needs to be pressed to check power level.
OPERATING INSTRUCTIONS
USED AS A BATTERY CHARGER
The MKS400 is intended, primarily, to be used to start or restart a
vehicle when the battery in the vehicle has become run down to the
point that it will not start the vehicle without assistance. However,
the MKS400 can also be used to restore some charge to the vehicle
battery.
1. Plug the DC power extension cord from the MKS400 into the
vehicle's cigar lighter outlet for 30 minutes.
NOTE: Some vehicle's ignition keys must be turned to accessory to
activate the cigar lighter socket.
2. Remove the DC power extension cord and start the car.
NOTE: A defective battery may refuse to accept a charge from the
MKS400.
USED AS AN EMERGENCY JUMP STARTER
NOTE: For optimum performance, do not store below 50°F when
using as a jump starter.
1.
Turn ignition off before making cable connections.
2.
Use in a well-ventilated area.
3.
SHIELD EYES.
4.
Clamp the positive (red +) clamp to the positive terminal on the
weak battery (for negative ground system).
5.
Clamp the negative (black –) clamp to the vehicle frame
(ground). Make sure the cables are not in the path of moving
belts or fan.
NOTES:
a.
If cables are attached in reverse, 888→REV will flash on
the display.
b.
When switch is in OFF position vehicle battery voltage is
displayed.
6.
Turn unit switch to the "ON" position. Display will flash
"888→SW→ON→Vdc".
7.
Stay clear of batteries while jump starting.
8.
Start the vehicle (turn on the vehicle ignition).
NOTE: If the vehicle does not start within 6 seconds, let the
MKS400 internal battery cool for 3 minutes before attempting
to start the vehicle again or damage to the MKS400 may
occur.
9.
When the vehicle is started, turn unit switch to "OFF" position,
disconnect the negative (–) battery clamp from the vehicle
frame.
10. Disconnect the positive (+) clamp.
USED AS AN ALTERNATIVE POWER SUPPLY
FOR VEHICLES
The MKS400 is an essential tool for all who replace automobile
batteries. Most vehicles have some type of electronic component
with memory, such as alarm systems, computers, radios, phones,
etc... and when the vehicle's battery is replaced, memory is lost.
However, if the cigar lighter power extension cord is plugged from
the MKS400 into the vehicle's cigar lighter socket, the memories can
be saved.
Note: Some vehicles may require the MKS400 to be connected to
the vehicle's OBD2 connector to save all memory functions. The
MS6209 memory saver may be purchased separately for these
applications.
MULTI PURPOSE POWER SUPPLY
The MKS400 is also a portable power supply for all 12 VDC
accessories equipped with a male cigar lighter plug or USB
connector. The DC outlet and USB port have automatic overload
protection.
To use the USB port, press and hold the Status button for 5
seconds, the display will flash "USB". To turn off the USB press and
hold the Status button for another 5 seconds, the display will flash
"USB OFF".
For maximum battery life do not discharge below 11V.
When the MKS400 is used with an inverter, it can operate
appliances normally powered by 120 VAC or 220 VAC in Europe.
Recommended inverter for the MKS400 is 300 watts maximum. For
more information contact your nearest MKS400 dealer.
!!! IMPORTANT !!!
BATTERY REMOVAL AND DISPOSAL
Contains sealed, non-spillable lead
acid battery. Must be disposed of
properly.
The battery inside this MKS400 is a sealed lead-acid battery.
By LAW, it is required to be removed and recycled or disposed of
properly. While there are regulations that must be followed
throughout your country, your local governments may have
additional regulations to be followed in your area.
When the battery in this product is in need of replacement, remove it
according to the instructions provided below and take it to your local
recycling center for proper recycling or disposal. If you don't have a
local recycling center that handles sealed lead-acid batteries,
contact your local environmental agency for instructions.
BATTERY REMOVAL INSTRUCTIONS
Begin by making sure the unit's power switch is in the "OFF"
position. You will need a T20 Torx head screwdriver and a 3/8"
socket.
1.
Remove (4) screws from display and pull display away from
unit. Note: Wire connections do not need to be disconnected.
3
Publicité
