Publicité
Les langues disponibles
Les langues disponibles
Operating instructions
LED Night-light with Motion Sensor
Item no. 1947429
Intended use
The product has to be connected to a power socket and serves as a night-light. It can be continuously
switched on via a switch (continuous light) or a PIR sensor.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Night-light
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of personal injury,
such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating manual that
absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• The device was constructed according to protection class II. Only a proper mains socket (220-
240 V/AC, 50 Hz) of the public supply net must be used as voltage source.
• Never use the product immediately after it has been brought from a cold room into a warm
one. The condensation generated could destroy the product. The plug-in power supply unit
also involves danger to life by electric shock! Allow the product to reach room temperature
before connecting it to the power supply and putting it to use. This may take several hours.
• Make sure the insulation of the whole product is neither damaged nor destroyed. The housing
must not be opened! There are no serviceable parts inside the housing.
• Never use the product if it is damaged. First, power down the respective mains socket and
then carefully unplug the product from the mains socket.
• Never touch the product if your hands are wet! Danger of electric shock!
• Unplug the product from the mains socket if you do not use it for an extended period of time.
• The device is not suitable for commercial use.
• Consult an expert when in doubt about operation, safety or connection of the device.
• Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
Overview
Operation
Check the product for damage before each use! If you detect any damage, DO NOT connect the
product to the power supply! There may be danger of life involved!
• Connect the night-light to a power socket.
The night-light must directly be connected to a power socket in the wall. Never use any extension
cables!
• Select one of the three possible operation modes using the "MOTION/ON/PHOTO" slide switch:
"MOTION" switch setting
• A built-in PIR motion detector switches the night-light on when a movement is detected and switches it off
after approx. 90 seconds. An additional twilight sensor prevents the night-light from being activated during
the day in daylight hours. For this reason, we recommend conducting a function test at twilight or at night!
The motion detection of the PIR motion detector is based on a heat difference between a moving
person and the ambient temperature (or a sufficiently large animal).
Do not point the PIR sensor directly to heaters or windows, as well as do not expose it to direct
sunlight.
• Please bear in mind that a warming up time of about one minute is necessary for the operation in the
"MOTION" mode (after being plugged in to an electrical outlet). During this time, the PIR sensor in the
night-light is adjusting to the ambient temperature. Only then does the PIR sensor work properly.
"ON" switch setting
• The night-light is continuously on. You can use this function, e. g., for the emergency lighting of a staircase.
"PHOTO" switch setting
• The built-in twilight sensor automatically activates the night-light if the ambient brightness is lower than the
pre-set threshold (e. g. in the evening). The night-light is automatically switched off again when it gets light.
Care and cleaning
• Disconnect the product from the power supply before cleaning.
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
• Clean the product with a dry, fiber-free cloth.
• Do not immerse the product in water.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to the protection of the environment.
Technical data
Operating voltage ................................. 220 - 240 V/AC, 50 Hz
Power consumption .............................. 0.6 W
PIR trigger ............................................ 8 ±3 Lux (on)
15 ±5 Lux (off)
PIR detection range .............................. 5 m (horizontal)
3 m (vertical)
Light source .......................................... 1 pc SMD LED
Colour temperature ............................... 5000 - 7500 K (cool white)
Brightness ............................................. 1.8 lm
Operating conditions ............................. 0 to 40 ºC, 0 – 85 % RH
Storage conditions ................................ -10 to +60 ºC, 0 – 85 % RH
Dimensions (W x H x D) ....................... 71 x 114 x 72 mm
Weight .................................................. 86 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also in
part, is prohibited. This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE.
1
MOTION/ON/PHOTO slide switch
2
LED cover
3
PIR sensor
4
Power plug
*1947429_v1_0319_02_dh_m_en
Publicité
