Sygonix 1780537 Mode D'emploi page 3

Operating instructions
Amorphous solar panel 12 V, 10 W
Item no. 1780537
Intended use
This amorphous solar panel is based on thin-film technology to allow the absorption of a wider
spectrum of natural light (normally sunlight). Even with a cloudy sky the module still delivers
an output. Higher outputs will also be generated at higher temperatures. With optimum solar
radiation, an output of 10 Watts is generated.
The solar panel is suitable for installation in outdoor areas.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use
the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Solar panel
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code shown. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is used when there is a potential risk of
personal injury, such as electric shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual that absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Materials are
to be observed.
• The product is designed for use outdoors.
• The solar panel generates power as soon as it is exposed to light. A single module
generates power below the so-called low voltage barrier. However, multiple
modules in parallel (summation of currents) or series connection (summation of
voltages) represent a potential risk. However, always consider the following notes
to avoid electrical shock, spark formation and fire:
- Solar panel(s) or the cables connected to it/them must never be installed with
damp or wet plugs or sockets.
- Never touch the connection leads or connection terminals with wet or damp
hands.
• Always use appropriate safety tools to install solar panels and look after your
own safety by wearing appropriate protective clothing (insulated tools, protective
gloves etc.).
- Never use damaged solar panels; never dismantle solar panels. Do not remove
type labels attached by the manufacturer.
- Ensure that there is a dry environment during installation and connection.
• Make sure that the solar panel is not subjected to mechanical forces. During
transportation, do not hold the solar panel by the terminal box; instead, always
carry it with both hands on the module frame. Bending, stacking, falls from a low
height, pressure as well as stepping on the solar panel will result in damage.
• Comply with all local regulations, accident prevention regulations as well as
construction regulations during installation and connection.
• Work on PV equipment (installation, connection, commissioning, maintenance,
repair) may only be carried out by qualified and authorised personnel.
• Personnel working on roofs 3 metres or more above ground, must be secured
against falls.
• Individuals must be protected from falling objects by fencing off the area.
• There is a risk of corrosion when exposed to salt and sulphur.
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Installation
Solar panels may only be used in a temperate climate. The solar panel is a device
that is not secured against explosions. Thus, it must not be installed in the vicinity of
highly inflammable gases and vapours.
Make sure that the installation equipment, installed together with this solar panel,
can support the loads assumed to result from wind and snow, for example.
If this solar panel is used in a system consisting of multiple solar panels, all modules
used must have the same amperage. Only solar panels with identical amperage
may be used when connected in series. Only solar panels with identical voltage may
be used when connected in parallel.
The panel has to be firmly fixed by at least four points.
The frame is suitable for fixing on the broad sides. The necessary holes have to be drilled.
Make sure that you do not damage the solar panel when drilling the holes.
When attaching the installation material make sure you do not damage the
subsurface, which may enable water to enter.
Use corrosion-resistant and suitable installation material for installation.
Shadow Free
Keeping the solar panel completely free from shadows is of the greatest importance. If the solar
module is shaded, less electricity will be produced and can - without a bypass diode connected
in series with other solar modules - put these partially out of operation. Even partial shading of
the solar module can lead to a loss of output.
Please note the following points:
• Select a south-facing roof area
• Roof pitch approx. 30º, but not less than 15º, to ensure sufficient self-cleaning from leaves,
snow and bird excrement.
• Keep the solar facade free from protrusions and balconies.
• Prevent shading caused by trees and buildings.
The most common sources of shade are:
- Chimneys, vent connections
- Trees (keep their future growth in mind)
- Gabled dormer windows
- Transverse gables etc.
- Make sure that the construction for fixing the solar panel does not shade the solar
panel.