Sunex Tools SX214A Instructions D'utilisation page 4

Nipple
Air Supply...
Tools of this class operate on a wide range of air pressures .
It is recommended that air pressure of these tools measures 90
PSI at the tool while running free . Higher pressure (over 90 psig;
6 .2 bar) raises performance beyond the rated capacity of the tool
which will shorten tool life because of faster wear and could cause
injury .
Always use clean, dry air . Dust, corrosive fumes and/or
water in the air line will cause damage to the tool . Drain
the air tank daily . Clean the air inlet filter screen on
at least a weekly schedule . The recommended hookup
procedure can be viewed in the above figure .
The air inlet used for connecting air supply, has standard 1⁄4" NPT .
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet) . Minimum hose diameter should be
3/8" I .D . and fittings should have the same inside dimensions and
be tightly secured .
Lubrication...
Lubricate the air motor daily with quality air tool oil . If no air line
oiler is used, run a teaspoon of oil through the tool . The oil can
be squirted into the tool air inlet or into the hose at the nearest
connection to the air supply, then run the tool . The amount of oil
to be used is one ounce . Overfilling will cause a reduction in the
power of the tool .
Limited Warranty...
SUNEX I NTERNATIONAL, I NC. W ARRANTS T O I TS C USTOMERS T HAT T HE C OMPANY'S S UNEX T OOLS ®
BRANDED PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex­ International, Inc . will repair or replace its Sunex­ Tools ® branded products which fail to give satisfactory service due to defective work-
manship or materials, based upon the terms and conditions of the following described warranty plans attributed to that specific product . This
product carries a ONE-YEAR warranty . During this warranty period, Sunex­ Tools will repair or replace at our option any part or unit which proves
to be defective in material or workmanship .
Other important warranty information...
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or
replacement made by anyone other than Sunex­ Tools or its authorized warranty service centers . The foregoing obligation is Sunex­ Tools' sole
liability under this or any implied warranty and under no circumstances shall we be liable for any incidental or consequential damages .
Note: Some states do not allow the ex­clusion or limitation of incidental or consequential damages, so the above limitation or ex­clu-
sion may not apply to you . Return equipment or parts to Sunex­ Tools, or an authorized warranty service center, transportation prepaid . Be
certain to include your name and address, evidence of the purchase date, and description of the suspected defect .
If you have any questions about warranty service, please write to Sunex­ Tools . This warranty gives you specific legal rights and you may also
have other rights which vary from state to state . Repair kits and replacement parts are available for many of Sunex­ Tools products regardless of
whether or not the product is still covered by a warranty plan .
Shipping Address: Sunex Tools • 315 Hawkins Rd . • Travelers Rest, SC 29690
Mailing Address: Sunex Tools • P .O . Box­ 4215 • Greenville, SC 29608
SX214A: Parts Breakdown & Operating Manual
Operation...
Before operating this sander, it is important to ensure that the
sanding pad is secure . To do this, hold the stop spanner (#48) on
the gear shaft and turn the pad clockwise until tight . Note: Make
sure dead handle is installed on appropriate side of sander for
positive grip while operating tool .
To change sanding discs:
Remove pad nut (#41), place abrasive disc on sanding pad, then
replace pad nut . Again, make sure pad is tightened securely .
Let the sander do the work . The normal weight of the machine is
sufficient for efficient sanding . Do not put ex­cessive pressure on the
machine . This will only slow down the speed of the pad, reduce
sanding efficiency and put an additional burden on the motor .
Start the sander off the work, set it down on the work evenly and
move it slowly back and forth in wide, overlapping areas . When
finished sanding, lift it off the work before stopping the motor .
4
Air Regulator
Air Inlet
rev. 04/9/06