Télécharger Imprimer la page

Publicité

Liens rapides

Installing the Handle. Refer to page 8 of the
1
operator's manual for more details.
Insert both sides of handle until pins click.
A
Connecting High Pressure Hose to Pump. Refer to
4
page 8 of the operator's manual for more details.
Use labels to identify and match parts. Then insert
A
the end of the high pressure hose into the threaded
nipple on the pump. Turn clockwise to tighten.
High Pressure
Hose
Adding gasoline. Refer to page 9 of the
7
operator's manual for more details.
Remove fuel cap. Insert funnel. Fill tank to
A
approximately 1-1/2 in. below the top of the tank
neck. Replace cap.
Use 87 Octane gasoline only. Do not mix oil with
gasoline.
Do not use E85 (Ethanol 85).
Verify that the On/Off Switch is in the ON
11
Position. (The On/Off switch is preset by the
factory to be in the ON position.)
988000141
05-07-10 (REV:01)
PS282411 QuICk STArT GuIDE
(NOTE: Page references refer to the Operator's Manual)
Assembling the Trigger Handle. Refer to page
2
8 of the operator's manual for more details.
Insert threaded end of spray wand into the
A
connector on the end of the trigger handle.
Turn connector clockwise until it stops.
Engage the lock-out when the
B
pressure washer is not in use.
A
Connecting Garden Hose. Refer to page 8 of
5
the operator's manual for more details.
Use labels to identify and match parts. Then
A
attach the end of the garden hose to the water
intake of the pump.
Garden
Hose
Installing the Nozzle. Refer to page 10 of the
8
operator's manual for more details.
A
Pull collar back.
Push tip into
B
quick-connect.
Release collar and it will click
C
into place
Pull the Starter Grip and rope. Refer
12
to page 10 of the operator's manual
for more details.
Give the starter grip 3 - 4 short, brisk
pulls to start the engine. If the engine
doesn't start after 4 pulls,
call customer service at
1-877-617-3501. Do not
return to store.
Connecting High Pressure Hose to Trigger Handle.
3
Refer to page 8 of the operator's manual for more
details.
Screw the collar on the high pressure hose into
A
the trigger handle inlet coupler by turning the hose
collar clockwise.
B
Adding/checking oil. Refer to page 9 of the
6
operator's manual for more details.
To add oil: Unscrew oil tip from oil bottle, then remove
A
foil seal. Replace oil tip. Remove oil cap from pressure
washer, then add oil by squeezing the entire contents
of the oil bottle into the oil reservoir.
To check oil: Remove dipstick and wipe clean.
Replace dipstick. Remove dipstick again and observe
oil level. Oil level should be at the top of full level
indicator. Replace oil cap.
Turn the Water Faucet Completely
9
On. Do not run the pump without
the water supply connected and
turned on.
B
S q u e e z e a n d H o l d
A
10
the Trigger for Thirty
Seconds to relieve excess
pressure trapped in
the system.
C
This Quick Start Guide is not a substitute for read-
ing the operator's manual. To reduce the risk of
injury or death, user must read and understand
operator's manual before using this product.
If you have any questions, please call:
www.powerstroketools.com
Product style and configuration may vary
WArNING:
1-877-617-3501.
TM
.

Publicité

loading

Sommaire des Matières pour PowerStroke PS282411

  • Page 1 PS282411 QuICk STArT GuIDE (NOTE: Page references refer to the Operator’s Manual) Installing the Handle. Refer to page 8 of the Assembling the Trigger Handle. Refer to page Connecting High Pressure Hose to Trigger Handle. Refer to page 8 of the operator’s manual for more operator’s manual for more details.
  • Page 2 PS282411 GuIDE D’uTIlISATION rAPIDE PS282411 guía inicial ráPida (NOTE : Les références de page se rapportent au manuel de l’opérateur) (NOTA: Todas las referencias a páginas se refieren al manual del operador) Assemblage de poignée de gâchette. Consulter la Branchement du flexible haute pression sur de poignée Installation du manche.