Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
SILLA DE TALLER PROFESIONAL NEUMÁTICA EZ SET™
EZ SET™ TABOURET D'ATELIER PNEUMATIQUE PROFESSIONNEL
EZ SET
PROFESSIONAL SHOP SEAT
Tools Needed for Assembly:
14mm Wrench
Assembly Instructions:
1. Attach all five (5) casters to bottom of round metal base. The bottom of the base is opposite the side with the center round hole.
Insert the threaded stem of each caster with lock washer through the holes and tighten nuts onto stem with a 14mm wrench.
2. Slip the painted end of the lift cylinder into center hole on top of round metal base. To avoid damaging the cylinder, do not force
or hammer cylinder into hole. The first time you sit on the seat, the cylinder will lock itself into place automatically.
3. Place seat on top of the unpainted end of the lift cylinder. As with the lift cylinder in Step #2, do not force or hammer the seat
onto cylinder.
4. To lock seat and cylinder into place, slowly add your weight to seat by sitting on seat for approximately 10 seconds.
5. You're done!
Care Instructions:
Your professional shop seat is designed to give you worry-free service with little to no maintenance. There should be no need for
periodic oiling or maintenance of the seat or cylinder. Simply keep clean with damp cloth. Avoid contact with harsh chemicals.
• Replacement air cylinder available as part # RS8509AC.
• Replacement caster with nut and washer available as part # RS8509WH.
• Replacement seat available as part # RS8509MST.
• Replacement bolt kit (5 nuts and washers) available as part # RS8509WK.
• Replacement plate with seat lever available as part # RS8509SL.
MAS4
PNEUMATIC
™
MAS4
Copyright © Professional Tool Products, 2018
All rights reserved.
rev 10/24/18
Publicité
Sommaire des Matières pour Matco Tools EZ SET MAS4
- Page 1 MAS4 SILLA DE TALLER PROFESIONAL NEUMÁTICA EZ SET™ EZ SET™ TABOURET D’ATELIER PNEUMATIQUE PROFESSIONNEL EZ SET PNEUMATIC ™ PROFESSIONAL SHOP SEAT Tools Needed for Assembly: 14mm Wrench Assembly Instructions: 1. Attach all five (5) casters to bottom of round metal base. The bottom of the base is opposite the side with the center round hole. Insert the threaded stem of each caster with lock washer through the holes and tighten nuts onto stem with a 14mm wrench.
- Page 2 If the manual or product labels are lost or not legible, contact Matco Tools for replacements. If the operator is not fluent in English, the product and safety instructions shall be read and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator comprehends its contents.
- Page 3 MAS4 SILLA DE TALLER PROFESIONAL NEUMÁTICA EZ SET™ EZ SET PNEUMATIC ™ PROFESSIONAL SHOP SEAT Herramientas requeridas para el ensamble: Llave 14mm Instrucciones de ensamble: 1. Sujete todas las cinco (5) rodajas al fondo de la base de metal redonda. El fondo de la base se encuentra al lado opuesto del lateral con el agujero central redondo.
- Page 4 MAS4 SILLA DE TALLER PROFESIONAL NEUMÁTICA EZ SET™ ADVERTENCIA HACER CASO OMISO A ESTAS ADVERTENCIAS PODRÍA OCASIONAR LESIONES. Lea y siga todas las instrucciones antes de usar este producto. • Lea y comprenda todas las instrucciones. Hacer caso omiso al seguir todas las instrucciones alistadas a continuación podría ocasionar el choque eléctrico, incendio, explosiones y/o lesiones personales serias.
- Page 5 MAS4 EZ SET™ TABOURET D’ATELIER PNEUMATIQUE PROFESSIONNEL EZ SET PNEUMATIC ™ PROFESSIONAL SHOP SEAT Outils nécessaires à l’assemblage : Clé 14 mm Instructions d’assemblage : 1. Attachez les cinq (5) roulettes à la face inférieure de la base de métal ronde. La face supérieure de cette base de métal est celle où...
- Page 6 état et dans un endroit accessible permettant au manuel d'être vu et lu par tous. Si le manuel ou les étiquettes du produit sont perdus ou illisibles, contactez Matco Tools pour les faire remplacer. Si l'utilisateur-opérateur de l'appareil ne maîtrise pas bien l'anglais, les instructions relatives au produit et aux mesures de...