Publicité
Les langues disponibles
Les langues disponibles
OWnEr'S mAnUAL
SETUP
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1. Depress the spring button at the bottom of the reference number (20) handle half and insert it in the reference number (22) lower handle
half until the spring button engages the hole in the lower handle half.
2. Remove the reference number (18) handle set screw from the reference number (17) handle yoke. Install the assembled handle into the
reference number (17) handle yoke making sure the bottom of the handle engages the release valve u-joint reference number (23).
3. Install the reference number (18) handle set screw in the reference number (17) handle yoke and tighten the screw to secure the handle
in the yoke.
PURGING AIR FROM THE HYDRAULIC SYSTEM:
a. Rotate the handle in a clockwise direction until tight. Now turn it in a counterclockwise direction two full turns.
b. Activate the pump 15 times.
c. Rotate handle in a clockwise direction until tight.
d. Activate the pump until the lift arm is raised to maximum height. You should experience a full pump stroke with each incremental
pump of the handle.
e. If it does not feel like you are getting a full incremental pump stroke at anytime during the pumping operation, repeat steps "a" through
"d" until all air is purged from the system.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
ImPOrTAnT: Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces.
OPERATION:
1. To raise load: Turn the handle in a clockwise direction until tight. Position the jack under the load.
Proceed to pump the handle in order to raise the lift arm to the load. As the saddle at the end of the lift arm gets closer
to the load, reposition the jack so the saddle will contact the load firmly and the load is centered on the saddle. Make sure the saddle is
correctly positioned. Raise the load to the desired work height. Place jack stands of appropriate capacity at the vehicle manufacturers's
recommended support areas that provide stable support for the raised vehicle. DO nOT CrAWL UnDEr VEHICLE WHILE LIfTIng
VEHICLE Or rEmOVIng THE JACK STAnDS! Once jack stands are positioned, turn the handle VERY SLOWLY. Lower the load to rest on
the jack stands. Inspect the relationship between the jack stands and load to make sure the setup is stable and safe. If the setup is not
stable or safe, follow the preceding steps until corrected.
2. To lower load: Follow the procedures mentioned in "To raise load" section of the OPERATING INSTRUCTIONS in order to raise the load
off the jack stands. Once the load has cleared the jack stands, remove the stands from under the load and away from the work area. Turn
handle very slowly in a counterclockwise direction until the load is completely lowered to the ground. Once the jack's lifting saddle has
cleared the load, remove the jack from under the load.
CAUTION: Keep hands and feet away from the hinge mechanism of the jack.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1.
Always store the jack in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow, sand or grit before using.
2.
The jack must be lubricated periodically in order to prevent premature wearing of parts. A general purpose grease must be applied to all
zerk grease fittings, caster wheels, front axle, elevator arm, handle base pivot bolts, release mechanism and all other bearing
surfaces.
3.
It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. If an external leak occurs
within the warranty period, bring the jack to any CARQUEST store for warranty disposition.
ImPOrTAnT: In order to prevent seal damage and jack failure, never use alcohol, hydraulic brake fluid or transmission oil in the jack.
4.
Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of the
jack but not any moving hydraulic components.
5.
Inspect the jack before each use. Do not use the jack if any component is cracked, broken, bent, shows sign of damage or leaks
hydraulic fluid. Do not use the jack if it has loose or missing hardware or components, or is modified in any way. Take corrective action
before using the jack again.
6.
Alterations and/or non-authorized repairs will void warranty.
EQP38748
3
EQP 38748
3 Ton Capacity
Aluminum Jack
rev. 04/03/09
Publicité
