Publicité
Les langues disponibles
Les langues disponibles
2. Operating instructions
2.1 Starting instructions
- Fit the battery on the tool and check the battery power via the 'on' button on the back of the
battery:
To check the remaining power while using the tool, press the button.
- Select the correct nosepiece and fit it on the tool.
- Ensure that the ventilation holes in the body are not covered or blocked.
- Ensure that the mandrel collector is installed on the tool.
- Empty the mandrel collector in time.
2.2 Operating instructions
- Insert the mandrel of the blind rivet fully into the nosepiece, place it in the pre-drilled hole of
the workpiece, start the operation by depressing the trigger.
- The blind rivet is set. As soon as the breaking point of the rivet is reached, the mandrel breaks
off and the trigger can be released. The jaw assembly automatically returns to the starting
position.
- Tilt the tool back so the rest mandrel falls into the mandrel collector, or tip the tool forward so
the rest mandrel falls out of the nosepiece.
- The blind riveter is equipped with overload protection. In the event of an overload, the tool
stops and a warning light is on. Release the trigger and the jaw assembly will return to the
start position.
2.3 Troubleshooting
2.3.1 Blind rivet is not set
Problems and causes
The red light on the battery powers on to
indicate low power
Battery damaged
Jaw assembly is loose
2.3.2 The rest mandrel does not slide into the mandrel collector
Problems and causes
Wrong nosepiece
Nosepiece worn out
Spent mandrel is stuck in the jaw assembly
Mandrel collector is full
Guide tube for the jaw presser is blocked
-
-
6
Solution
Charge battery
Replace battery
Secure jaw assembly
Solution
Fit the correct nosepiece
Replace nosepiece
Unscrew the jaw assembly, clean the jaw
assembly, and lubricate it
Empty mandrel collector
Remove the mandrel and check that all parts
have been removed from the guide tube
2.3.3 The red warning light is lit
Problems and causes
Jaw assembly does not return to start
position
Overload (warning light is on)
Overheated
Discharged battery
NOTE: If the solutions provided above have no effect, the tool must be repaired by qualified
personnel or returned to the dealer or manufacturer's representative.
3. Battery and charger
3.1 Technical data
Battery
Weight lithium battery:
0.38 kg
Related voltage:
20V
Capacity:
2.0Ah
3.2 Battery charging and safety instructions
- Only charge batteries supplied by authorized dealers;
- Always use the original power supply intended for this tool;
- Before charging the battery, please read the warning label of the charger and the battery;
- Do not use a damaged charger to charge this tool;
- Never attempt to charge a damaged battery;
- Never place a dirty or wet battery in the charger;
- Never dispose of batteries with household waste or in fire or water;
- Neither the charger nor the lithium battery should be placed in water, exposed to water,
snow or any type of wet environment;
- If the battery leaks liquid, avoid contact with this liquid; if there is any contact with this
liquid, rinse it off with water and immediatly consult a doctor;
- The ambient temperature of charging and discharging is 0
- When storing the battery for longer periods of time (more than 3 months), the battery must
be kept at a temperature of approx 23
0
NOTE: the battery is not fully charged when it leaves the factory. In order to ensure the full
function of the battery, please fully charge it before using. Pay attention to the charging
qonnect-fasteners.com
Solution
Release the trigger
Check whether the blind rivet is suitable for
the tool. Remove the battery once to reset
Remove the battery and allow the tool to cool
in the open air
Recharge the battery or replace if necessary
Charger
Input voltage:
100-240VAC/50-60 Hz
Charging time:
<60min
Output voltage: 20V
Weight:
0.37 kg
0
C up to max 40
0
C;
C, but no lower than 18
0
C and no lower than 28
0
C.
-
-
7
Publicité
