Publicité
TCUNØ6_toflashat100% 27/09/13 17:07 Page2
EN
1) BaTTeRies:
This product requires 2 AAA/LR03 Alkaline
batteries. Please pay attention. To the pola-
rity +/-.
aTTeNTioN: to keep the codes stored in-
side the memory do not. Press any key du-
ring batteries replacement.
2) diRecT code
TV
1) Turn on the device.
2) Look for the brand of the device you want
to program in the code list and Make a
note of the first code in the list (e.g Philips
TV - 0024).
3) Press and hold the device key of URC
around 5 seconds until LED goeson. Then
release.
4) When the LED goes on in step 3, enter the
previously identified code (e.g. 0024) from
the code list.
If LED turns off, it indicates that the code is
accepted. (If LED flashes 3 Times and then
turned off, it indicates the code is unaccep-
ted. Repeat from Step 3 ).
5) Then press [POWER] of URC to see if it
can turn off the device. If it can turn off the
appliance, it means the code is correct; if
not, please repeat from step 2 to try ano-
ther codes.
N.B. THE LED STOPS FLASHING. The re-
mote control exits programming mode and
the LED stops flashing If no keys are pres-
sed for 15 seconds.
dTV, saT, auX, dVd or VcR
To set all other devices, repeat the same
operation as with the TV, by pressing the but-
ton on the remote for the device you want to
program.
N.B. : during the programming, the LED
turns off if no button is pressed on the remote
control for a period of 15 seconds or more.
In this case, repeat the procedure from the
beginning.
3) PoWeR auTo-seaRchiNG
This operation can take up to 20 minutes and
should be carried out if you havenot succee-
ded in programming the remote control by
means of "Direct code entry".
TV
1) Turn on the appliance to be programmed.
2) Press and hold the device key around 5
seconds until LED goes on. Then release.
3) When LED goes on in step 2, Hold the re-
mote control and aim to the device. Press
and slowly release the [POWER ] key,
LED flash once every two seconds.
4) When the appliance powers off, it indi-
cates that the code is found.
5) Appuyez sur la touche On/Off pour allu-
mer l'appareil et essayez les différentes
touches de la télécommande.
6) Switch on the device and check the va-
rious keys on the remote, if the found code
is not correct please repeat from step 2
If the end of the code search list has been
reached. In this case, start again from Step
2.
code RemiNdeR: In case you forget the
codes entered in the URC, please follow
these steps to find out the 4 digits codes.
1) Press and release device key (according
to the code that you want to know led will
flash once.
2) Press and hold device key, then press OK,
release both of them, led will once.
3) Led will indicate the digit code with a se-
ries of flashes separated by a brief pause.
Ex code 1380:
- 1 flash followed by a pause of 1 sec. = 1
- 3 flashes followed by a pause of 1 sec. = 3
- 8 flashes followed by a pause of 1 sec. = 8
- 10 flashes followed by a pause of 1 sec. = 0
dTV, saT, auX, dVd or VcR
To set all other devices, repeat the same
operation as with the TV, by pressing the but-
ton on the remote for the device you want to
program.
1) Pi
Ce pro
(LR03
diqué
téléco
NB :
chang
lez à
dant
perdre
2) sa
TV
1) Allu
2) Ch
list
002
3) Ap
con
jus
lâc
4) Sa
dan
été
Si le
cligno
alors
5) Un
de
sai
On
de
Si tou
recom
2 ave
marqu
TNT,
Pour
répéte
en ap
la télé
que v
N.B. :
voyan
touch
de 15
cédur
Publicité
