Product Overview; Technical Data - TOOLCRAFT 1553068 Mode D'emploi

Product overview

9
8
7
1 Glue stick
2 LED indicator
3 Handle
4 Heating station
5 Power jack
Operation
• Attach the stand bracket to the product.
• Put a glue stick (Ø11 mm) into the feeding tube. Press the trigger to advance the glue stick
into the feeding tube.
• Connect the power cord to the heating station first and then to a common household power
outlet.
• Connect the connector on the bottom of the handle with the corresponding connector on the
heating station. The red indicator light is lit and the product starts to heat up.
• Let the product heat up for 3 to 5 minutes.
• Disconnect the product from the heating station.
• Press the trigger to make the liquid adhesive exit the nozzle.
• When the adhesive is thick and the feed rate sluggish, reconnect the product with the heating
station.
You can also connect the product directly to the power cord without using the
heating station.
• Disconnect the product from the power supply after working.
Do not pull the glue stick out of the product. The remaining glue stick can remain in
the product once you have finished working.
Changing the nozzle
Warning! Before changing the nozzle, ensure that the product has cooled down
completely. Otherwise there is a danger of burning!
The long nozzle is suitable for bonding in hard to reach places as well as for filling
cavities, holes etc.
• Carefully pull the silicone protection from the nozzle.
• Remove the nozzle from the product.
• Place the other nozzle onto the thread and use a suitable tool to tighten the nozzle.
• Pull the silicone protection over the nozzle.
• The product is now ready for use.
1 2
6 Mains cable
7 Stand bracket
8 Nozzle
9 Trigger
Tips for glueing
• The bonding surfaces must be free of dust and grease, and dry. Do not use flammable
detergents and solvents.
• Zigzag lines of glue are good for glueing flexible materials (e.g. textiles).
Beads of glue are good for glueing all other materials.
• Press the trigger carefully and apply the adhesive to the parts to be glued. These parts can
be glued together within 15-20 seconds. If necessary, insert new glue sticks into the product.
• The bonding time is approximately 30 seconds and about 90 % of adhesion occurs after one
minute. The bonding time for thick beads of glue can be longer or shorter for small ones.
• Do not glue large areas at once, but work in sections. Apply the adhesive in a corrugated
pattern.
• You can increase adhesion by preheating the surfaces to be glued together, e.g. with a hot
3
air gun.
• Only remove adhesive residue when cold.
4
• You can loosen or adjust glued areas by heating them, e.g. with a hot air gun.
5
• If you wish to glue two different materials together, first apply adhesive to the harder material.
• The liquid adhesive can fill small holes and cracks.
Troubleshooting
6
Problem
The product does not turn on.
The adhesive is not liquid enough.
Care and cleaning
• Always disconnect the product from the power supply before cleaning it.
• Let the product cool down completely.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
damage the casing or cause the product to malfunction.
• Use a dry, lint-free cloth to clean the product.
Disposal
Electronic devices are recyclable waste and must not be placed in household waste.
Always dispose of the product according to the relevant statutory regulations.
You thus fulfill your statutory obligations and contribute to the protection of the
environment.

Technical data

Operating voltage ......................... 220 – 240 V/AC, 50 Hz
Power consumption ...................... 25 W (standby), 500 W (heating up)
Heating-up time ............................ 3 – 5 min
Melting temperature ...................... 170 °C
Output ........................................... 16 – 20 g/min
Cable length ................................. 1.5 m
Weight .......................................... 600 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
Possible cause and solution
Check to see if the power cord is correctly
connected with the product and the power
outlet.
The power cord is damaged. Replace it with
an identical power cord.
The product is overheated. Disconnect the
plug and let the product for cool for several
minutes before you try again.
The heating-up phase was too short. Let
the product heat up longer.
You have waited too long and the adhesive
has rehardened. Use the glue immediately
once melted.
*1553068_v1_0917_02_IPL_m_en