Yakima 8002094 Guide Rapide

InstallatIon
Is a 3-part process:
- remove Front Wheel
- Install Fork adapter
- attach to Bike rack
Install Fork adapter:
Attach the FORK AdApteR while your bike is still on the ground.
• Install fork on adapter and fasten according to Maverick
fork installation instructions.
FORK AdApteR legs must run parallel with the fork
leg, unless you are running several bikes on your
rack. Conflicting handlebar heights require the FORK
AdApteR to be rotated (maximum of 180°).
attach to Fork-moUnted BIke rack
• Check that all bolts are tight and the FOrk adapter is
securely attached to your fork.
• attach the FOrk adaPter onto your fork-mounted rack.
(Follow the manufacturer's directions on tightening
down the quick release before driving away.)
• Be sure FORK AdApteR and bike are both mounted
securely to your bike rack before driving.
• do not exceed the weight limit recommended by the
bicycle fork mount or vehicle manufacturer.
BeFore rIdIng:
• Check your fork bolts, making sure
all bolts are tight and secure and that
your front brake works properly.
• Off-road driving is not recommended
and could result in damage to your
vehicle or your bike.
teCHNICaL aSSIStaNCe Or
rePLaCeMeNt PartS
Contact your dealer or call (888)925-4621
Monday through Friday,
7:00 aM to 5:00 PM, PSt
IMPORTANT WARNING: IT IS CRITICAL THAT ALL YAKIMA RACKS AND ACCESSORIES BE PROPERLY AND SECURELY ATTACHED TO YOUR VEHICLE.
IMPROPER ATTACHMENT COULD RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH TO YOU OR TO
OTHERS. YOU ARE RESPONSIBLE FOR SECURING THE RACKS AND ACCESSORIES TO YOUR CAR, CHECKING THE ATTACHMENTS PRIOR TO USE,
AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR, AND DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND
ALL OF THE INSTRUCTIONS AND CAUTIONS SADAPTERPLIED WITH YOUR YAKIMA PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT
UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR
WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER SUCH AS A QUALIFIED
GARAGE OR AUTO BODY SHOP.
1033416A-1/2
24 mm Fork Adapter
remove Front Wheel:
• Open QuickFlip lever.
• Pull out your axle.
maIntenance
Periodically check for excessive
wear, including rust or cracks.
replace if cracked or rusted.
reMOVe aCCeSSOrY BeFOre
eNterING aN aUtOMatIC Car
WaSH.
k e e p t h e s e
This figure may differ from your fork.
Follow your fork manufacturer's directions for wheel
removal, axle and axle bolt location and tightening.
QUICKFLIP LEVER
FOrk adaPter
to remove Fork adapter
(
do not leave FORK AdApteR attached to your rack.)
• remove the bike from your rack with the FOrk
adaPter still attached to your fork.
• Set the bike on the ground, and open
Maverick QuickFlip levers.
• Slide out the axle from the FOrk adaPter and
remove the FOrk adaPter.
• Insert your front wheel; and fasten according to
Maverick fork installation instructions.
this product is covered by YAKIMA's "Love It till
You Leave It" Limited Lifetime Warranty.
to obtain a copy of this warranty, go online to
www.yakima.com or email us at
yakwarranty@yakima.com or call (888) 925-4621
I n s t r U c t I o n s !
different manufacturers have
different methods of wheel
removal, follow your fork
manufacturer's directions.
FORK LEGS
AXLE
QUICKFLIP LEVER
WarnIng:
Be SUre aLL HardWare IS
SeCUred aCCOrdING tO
INStrUCtIONS. attaCHMeNt
HardWare CaN LOOSeN
OVer tIMe. CHeCk BeFOre
eaCH USe, aNd tIGHteN IF
NeCeSSarY.
Part #1033416 Rev.A